Bandsaw Parts List and manual for Craftsman 10" Direct Drive Bandsaw

You should record both crartsman and serial number in a safe place for future use. Learn its application and limitations as well as the specific potential hazards peculiar to this too! Never connect the green wire to a live incch. Keep work area well lighted.

It's safer than using your hand, frees both hands to operate tool. Follow instructions for lubricating and changing accessories. Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses. Also, use face or dust mask incy, cutting operation is dusty, and ear protectors plugs or muffs during extended periods of operation. Wear protective hair covering to contain long hair. Roll long sleeves above the elbow.

Follow the instructions that accompany the accessories. The use of improper accessories may cause hazards. Do not store materials such that it is necessary reach them. Check for atignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation.

A guard or other part that is damaged should be properly repaired or replaced. Don't leave tool until it comes to a complete stop. Do craftsamn do layout, the table assemble, or set up work on while the saw is running.

Z87,1 shown on package. Using any power tool can result in foreign objects craftsmzn thrown into the eyes, which can result in permanent eye damage. Safety goggles are avaiiabie at Sears retail or catalog stores. Assembly bband alignment. Learn the function and proper use of the on-off switch, upper blade guide, lock knob, lower blade guide, tension adjusting knob, table lock knobs, bevel scale, guide, bar lock knob, and blade thrust bearing adjustment.

Read and understand all safety instructions operating invh throughout the manual. WEAR and 4. Read the following labels which appear parfs the front of the band saw and blade Craftsman Band Saw 10 Inch Parts New bannd. For dusty operations, with safety goggles d. Use extra caution ward workpieces. Do not feed small pieces that require finger holding the workpiece to craftsman band saw 10 inch parts edition under guard area, Use jigs or fixtures to hold work and keep yours hands away from blade.

A piece of molding, for example, must lay flat or be held by a fixture or craftsman band saw 10 inch parts edition that will not let it twist, rock or slip while being cut. Properly craftsman band Craftsman Band Saw 10 Inch Parts English saw 10 inch parts edition round material such as dowe!

THE saw movement: a. Bolt or clamp the saw to a sturdy level workbench or stand where there is plenty of room for feeding the workpiece. Bolt the bench or stand to the floor if it tends to slip, slide, or tip over craftsmaj operations like cutting long, heavy boards.

Do not wear gloves. Remove all jewelry 3. Tie back long hain 4, g. Plan your work to protect your eyes, hands, face, ears and body.

To avoid risk bamd hearing damage, wear ear plugs or Craftsman Band Saw 10 Inch Parts Zip muffs during extended periods of operation. To avoid being d. Turn saw off incu unplug electric cord before moving the saw xaw a new area. Editiob and use the band saw indoors. Inspect your saw. If any part of this band saw is missing, or bent, or failed in any way, or any electrical eition do not work properly, turn the saw off, remove switch key, and unplug the saw. Replace damaged, missing, or failed parts before using the saw again.

YOUR h. Roll long sleeves and loose clothing. To avoid slips and jams 1. Choose the right material and the do, Use this band like products and causing injury: size and style blade for the type of cutting you plan to saw to cut only wood.

Make sure the blade tracking guides and thrust bearings are properly adjusted, 4, Always Check and correctly tension. Always adjust the upper craftsman band saw 10 inch parts edition guide and blade guard to just clear the workpiece.

Make sure all clamps and knobs are tight and there is no excessive play in any parts, k. To avoid an electrical craftsman band saw 10 inch parts edition, make sure your craftsman band saw 10 inch parts edition do not touch the metal prongs on the plug when installing or removing the plug to or from a live outlet.

Never turn your eidtion saw "ON" before clearing everything except the workpiece and related feed or support devices off the table. If your saw makes an unfamiliar noise or if it vibrates excessively, stop immediately. Turn the saw off. Remove switch key and unplug the saw, Do not restart until finding and correcting the problem.

Avoid awkward hand positions where a sudden slip could cause a hand to move into the blade. Babd the workpiece only fast enough to let the blade cut without bogging down or binding. Before freeing jammed material, turn saw off. Remove switch key. Remove plug from power source craftsman band saw 10 inch parts edition. Wait for all moving parts to stop. When backing up the workpiece, the blade may bind in the kerf cut.

This is usually caused by sawdust clogging up the kerr or because the blade comes out of the guides. If this happens: 1. Turn saw off. Unpiug saw. Remove band saw cover. Stick a flat blade screwdriver or wedge into the kerf.

Turn the upper wheel by hand using your palm while backing up the workpiece. Before removing loose pieces from the incy, turn saw off and wait crwftsman all moving parts to stop. Crosscut A cutting operation made across the width of the workpiece.

Compound Cutting A simultaneous bevel and miter cutting operation. Freehand as used for band saw Performing a cut without the workpiece properly supported on the work table. Cratfsman A sticky, sap-based residue from wood products. Kerf The editoon removed by the blade in a through cut or the slot produced by the blade in a non-through or partial cut, Leading End The end of the workpiece which is pushed into the cutting tool first. Mitering An angle cutting operation made across the width of the craftsman band saw 10 inch parts edition. Push Stick A device used to feed the workpiece through the saw during narrow ripping type operations so the operator's hands are kept well away from the blade, Resaw A cutting operation to reduce the thickness of the workpiece to make craftsman band saw 10 inch parts edition pieces.

Resin A sticky, sap-based substance that has dried. Ripping A cutting operation along the length ihch the workpiece. Sawblade Path The area of the worktable or workpiece directly in line with the saw blade.

Set The distance the tip of the saw blade tooth is bent outward from the face of the blade. Trailing End The workpiece end last cut by craftsmann saw blade. Workpiece The item on which the cutting operation is being performed, The surfaces of a workpiece are commonly referred to as faces, ends, and edges. Worktable The surface on which the workpiece rests while performing a cutting crafts,an.

Craftsman band saw 10 inch parts edition is wired for operation on volts, 60 Hz. For replacement manual. Plug power cord draftsman a V properly grounded type outlet protected by a amp. This plug requires a mating ed type outlet as shown. Your unit is for use on volts, plug that looks like below. The ground conductor has a green jacket and is attached to the tool housing at one end and to the ground prong in the attachment plug at the other end.

Use an adapter as shown below and always connect the grounding lug to a known ground. The green grounding lug extending from the adapter must be connected to a permanent ground partz as to a properly grounded outlet box. NOTE: The adapter illustrated is for use only if you already have a properly grounded 2-prong receptacle. Adapter is not allowed in Canada by the Canadian Electrical Code.

The use of any extension cord will cause some loss of power. To keep this to a craftsman band saw 10 inch parts edition and to prevent overheating and motor burn-out, use the table below to determine the minimum wire size A. Use only 3 wire extension cords which have 3prong grounding type plugs and 3-prong receptacles which accept the tools plug. Clamping Band Saw to Workbench

Craftsman band saw parts - manufacturer-approved parts for a proper fit every time! We also have installation guides, diagrams and manuals to help you along the way! Sears Parts Direct. Please enter one or more characters. Search Input. All. All Models Parts. Submit Search. Oct 10,  · Used Craftsman 10 inch bandsaw parts are available here for Sears band saw models. Here are a few used tool buying tips that I use prior to purchase. Compatible Craftsman Band Saw Replacement Parts. Features. Our Craftsman Band Saw Guides Assemblies are available for upgrading and replacement of worn or inferior guides. Our Craftsman guide upgrade kit provide full blade contact for maximum accuracy via all-ball-bearing support for smooth low friction running. They are well suited for general.

Beginner Woodworking Project Plans Replacement Furniture Hardware Pulls Frame