Never sand without a table supporting the stock. Page belt and disc sander safety rules of Assembly and adjustments continued Mounting the Sander to the Workbench CAUTION: If during operation there is any tendency for the sander to tip over, slide or walk on the supporting surface, the sander should be properly mounted to a workbench or stand. Remove the used sanding disc. Utilize an extension cord of appropriate weight. Always keep your fingers, hands, and other parts of your body out of the danger zone. Shopping Cart. Turn the power switch to OFF.

Holding the table in this position, tighten the three bolts on the top of the table. Note: The table may have to be re-adjusted when tilted. Page 13 Assembly and adjustments continued Mounting the Sander to the Workbench CAUTION: If during operation there is any tendency for the sander to tip over, slide or walk on the supporting surface, the sander should be properly mounted to a workbench or stand.

Page 14 Assembly and adjustments continued Sanding belt tracking adjustment 1. Plug in the power cord. Turn the switch ON and OFF to make sure the sanding belt is correctly centered and not sliding off the idler and drive roller drums. Page 15 Assembly and adjustments continued Install a sanding disc 1. Remove the two screws from the sanding disc guard and remove the guard.

Remove the used sanding disc. Wipe the sanding disc plate clean. Peel the backing from the new sanding disc, align the disc with the plate and press the sanding disc firmly on to the plate. Page 16 Assembly and adjustments continued Square the tables To ensure accurate end sanding, the work tables must be square to the sanding surfaces prior to using the tables for disc sanding.

Place the key in a safe place and out of the reach of children. Page 18 Operation continued End sanding and outside curve sanding with the disc Use for sanding the ends of small and narrow workpieces and outside curved edges. Always work on the left side of the disc downward rotation side , holding the workpiece firmly with light pressure against the sanding disc. Page 19 Operation continued Miter gauge — Disc sander A miter-gauge is supplied with your sander, and can be used on the disc table.

Page Maintenance Maintenance continued Adjust the Drive belt 1. Remove the drive belt housing cover 1. Loosen the 3 screws 2 allowing the pulley to slip and the drive belt 3 to loosen.

The drive belt should be seated correctly in the motor pulley and the drive pulley. Page Troubleshooting Troubleshooting Service on these tools should only be performed by an authorized, qualified technician. Problem Cause Solution Sanding Grains easily 1. Ensure sanding accessories are rub off belt or discs. Page 22 Problem Cause Solution Motor 1. Motor overloaded. Reduce load on motor pressure on overheats.

Extension cord too long object being sanded. Utilize an extension cord of appropriate weight. Print page 1 Print document 25 pages. Cancel Delete. Sign In OR. Don't have an account? Sign up! Written by Doityourself Staff. Important safety tips Never change the sandpaper while the sander is plugged in. Make sure that there is no electrical current connected to the tool before making any changes.

Place the tool onto the wood surface you are going to be working on before turning on the power switch. When you are finished working, do not remove the sander from the wood until you have turned the tool completely off. Wear protective eye material and use a respirator.

Belt sanders can kick up a lot of dust that is harmful. Only use a belt sander that has a proper dust ventilation system included. If it does not come with one, most shop vacuums can be attached and work with the same efficiency. Things to Avoid With a Belt Sander. Related Posts "Starter sets" needed: Blades, sanding discs and belts. Hello all!

I have the following tools and seek recommendations on "starter Read More. Brushing steel - the basics. Hello there I'm a woodworker starting to use metal in some of my designs I messed up my hardwood floor Painted floor problem. I mistakenly painted semi-gloss over high-gloss paint on my porch floor and Skill ct3 3inch belt sander On the motor the numbers volts SEY

Delta 900 Radial Arm Saw Error Diy Wood Mantel Cover 600 Kiln Dried Wood For Turning