Buy as much as you need. Smart Guard System The surfaces of a workpiece are commonly referred to as faces, ends and edges. Upload from URL. Quick Links. Inspect extension cords periodically and replace if damaged.

For example: pipes, radiators, ranges, refrigerator enclosures. Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted. Do not store materials on or near the tool such that it is necessary to stand on the tool or its stand to reach them. Before further use of the tool, a guard or other part that is damaged should be carefully checked to ensure that it will operate properly and perform its intended function.

Check for alignment of moving parts, mounting and any other con ditions that may affect its operation. A guard or other part that is damaged should be properly replaced. All repairs, electrical or mechanical, should be attempted only by trained repairmen. Accessories that may be suitable for one tool, may become hazardous when used on another tool.

Use clamps or a vise to hold work. Feed work into a blade or cutter against the direction of rotation of the blade or cutter only. These tools are precision built. Any alteration or modification not specified is misuse and may result in dangerous conditions.

Do not operate electric tools in gaseous or explosive at mospheres. Motors in these tools normally spark, and may result in a dangerous condition. Keep tools sharp and clean for better and safer performance.

Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and if damaged, have repaired by authorized service facility. Inspect extension cords periodically and replace if damaged. Keep handles dry, clean and free from oil and grease. Before connecting the tool to a power source receptacle, outlet, etc. A power source with voltage greater than that specified for the tool can result in serious injury to the user — as well as damage to the tool. Using a power source with voltage less than the nameplate rating is harmful to the motor.

For your own safety, do not operate your! General Safety Rules. Double Insulated Tools. Basic Table Saw Operation. Maintaining Your Table Saw. In addition, if there is any tendency for the table saw to tip over or move during certain operations such as cutting long, heavy boards, use an auxiliary support.

Use the table saw in a well lit area and on a level surface, clean and smooth enough to reduce the risk of trips and falls. Use it where neither the operator nor the casual observer is forced to stand in line with the blade. Workpiece binding the blade due to misalignment, can also cause kickback. During kickback, workpiece rises from table and is thrown toward the operator.

Maintaining the rip fence parallel to the sawblade. Keeping the sawblade sharp. Replacing or sharpening anti-kickback pawls when points become dull. Keeping sawblade guard, spreader and anti-kickback pawls in place and operating properly.

The spreader must be in alignment with the sawblade and the pawls must stop a kickback once it has started. Check their action before ripping.

NOT ripping workpiece that is twisted or warped or does not have a straight edge to guide along the rip fence. NOT releasing work until you have pushed it all the way past the sawblade. NOT confining the cut-off piece when ripping or crosscutting. When ripping, apply the feed force to the section of the workpiece between the sawblade and the rip fence. If any part of your saw is missing, malfunctioning, has been damaged or broken … such as the motor switch, or other operating control, a safety device or the power cord … cease operating immediately until the particular part is properly repaired or replaced.

Wear safety goggles and a face shield if operation is dusty. Wear ear plugs or muffs during extended periods of operation. Small loose pieces of wood or other objects that contact the rear of the revolving blade can be thrown back at the operator at excessive speed.

Use extra caution when the guard assembly is removed for resawing, dadoing, rabbeting or molding — replace the guard as soon as that operation is completed. NEVER place your face or body in line with the cutting tool. Avoid awkward operations and hand positions where sudden slip could cause fingers or hand to move into a sawblade or other cutting tool.

DO NOT use the rip fence as a length stop. However, since these are usually quite hard and slippery, the anti-kickback pawls may not stop a kickback. Therefore, be especially attentive to following proper set-up and cutting procedures for ripping.

Do not stand, or permit anyone else to stand, in line with a potential kickback. If ripping at the time, check to see if rip fence is parallel with the sawblade.

Readjust as indicated. NEVER gang crosscut — lining up more than one workpiece in front of the blade stacked vertically, or horizontally. The blade could pick up one or more pieces and cause a binding or loss of control and possible injury.

DO NOT remove small pieces of cut-off material that may become trapped inside the blade guard while the saw is running. This could endanger your hands or cause a kickback. Dull, gummy or improperly sharpened or set cutting tools can cause material to stick, jam, stall the saw, or kickback at the operator.

Minimize potential injury by proper cutting tool and machine maintenance. NEVER use grinding wheels, abrasive cut-off wheels, friction wheels metal slitting blades wire wheels or buffing wheels. Crosscutting operations are more conveniently worked and with greater safety if an auxiliary wood facing is attached to the miter gauge.

See Page Make sure the top of the cutting tool rotates toward you when standing in normal operating position. Also make sure the cutting tool, arbor collars and arbor nut are installed pro p- erly. Keep the cutting tool as low as possible for the operation being performed. Keep all guards in place whenever possible.

Never use a cutting tool larger in diameter than the diameter for which the saw was designed. For greatest safety and efficiency when ripping, use the maximum diameter blade for which the saw is designed, since under these conditions the spreader is nearest the blade. Make sure the table insert is flush or slightly below the table surface on all sides except for rear side.

NEVER operate the saw unless the proper insert is installed. Do not allow familiarity gained from fre-! Always remember that a careless fraction of a second is sufficient to inflict severe injury. The operation of any power tool can result in foreign objects being thrown into the eyes, which. Some dust created by power sanding,! Some examples of these chemicals are:. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

If your tool is equipped with a po arl zedi plug one blade is wider than the other , this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. To reduce the risk of electric shock, do not change the plug in any way. Always use proper extension cord. If an extension cord is necessary, a cord with adequate size con ductors should be used to prevent.

The table shows the correct size to use, de pending on cord length and nameplate amperage rating of tool. If in doubt, use the next heavier gauge. Always use U. NOTE: The smaller the gauge number, the heavier the cord. Also See for Operating instructions manual - 56 pages. Quick Links. Table of Contents. Consumer Information. For English Version. Instrucciones de funcionamiento y seguridad.

Pour obtenir des informations et. Previous Page. Next Page. Maintaining the rip fence parallel to the sawblade. These tools are precision built. Any alteration or modification b. NEVER place your face or body in line with the cutting outward on the table and then pushing thru sawblade.

The tool. In general, heel cre- The item on which the cutting operation is being performed. Learn more. Returning it would cost more than the part itself so in the trash it goes.

Skip Navigation Sears home. Shop Your Way Pinterest Email. Which list would you like to add your item to? Wish List. Includes 1 Miter Gauge. New, Bulk Packed. Genuine OEM replacement part. Consult owners manual for proper part number identification and proper installation. Compatible with: Skil : 10" Table Saw. Added on March 12,

Plan Chaise Adirondack Bercante De Jet Plane Cartoon Game