The only down side is that it does not come with both left and right stick on tape measures. Just peel off the backing and stick anywhere. Incra - Miter Gauge SE. The stop flips out of the way osborne miter gauge instructions remote not in use and abrasive tape on instrucgions fence face prevents workpiece slippage. It has a nice solid feel and on checking with a digital angle protractor, I couldn't fault it. Wow, am I glad I have one of these!

The fence can also be adjusted from side to side, allowing tight clearance to the blade, and the entire assembly is reversible in seconds for use in either miter slot. A removable heavy-duty steel T-slot washer holds the guide bar snug to the table, while the three guide bar expansion screws remove any play in the miter slot. A simple-to-use lockable calibration mechanism allows you to make precision angle adjustments when needed.

Osborne EB-3 Miter Gauge. Patented triangular design offers rock-solid support of the fence and workpiece at any angle setting. Item Skip to the end of the images gallery. Skip to the beginning of the images gallery. Strong magnets securely attach this gauge to the top of your table saw, miter saw or jointer table, where you set the zero calibration with the touch of a button.

No need for the equipment to be perfectly level. Then just set it on your fence or blade and precisely lock in the exact angle you need. Joints are cleaner and tighter. Fit and finish is visibly improved when you can cut close tolerance dimensions.

The precision readout uses what's called capacitive measuring technology. This is the exact same system that is used in almost all digital calipers that have been on the market for at least 20 years. There is a circuit board on a rotating counterweight that has a repeating pattern etched on it. There is a second fixed circuit board with a similar pattern and the rest of the electronics. As the 2 patterns pass over each other there is an electronic signal generated that is converted to rotation angle.

The only moving part is the circuit board with counterweight passing over the fixed circuit board. The tool has a large surface to control movement of the wood.

My old original equipment mitre gauge was always a struggle to keep wood square to the saw blade when making cuts. I already owned a miter gauge for my table saw,but I tend to use the Osborne because it is easy to adjust and produces accurate cuts every time. The only down side is that it does not come with both left and right stick on tape measures.

The triangular support arm assures a consistent and reliable cut. The design is so simple and reliable I am still astounded that no other miter gauge I've seen has this design. Forget the pricey, multi-colored protractor-type of miter gauges and put your money down on this product.

The first time you make a 90 degree cut and slap an engineer's square up against the cut, you will see what I mean.

I have always struggled on the table saw to get true miters at any angle. The Osborn miter gauge after it was calibrated has been dead on every time. It was a little off right out of the box, but the adjustment method in the assembly instructions was quick and easy. Only about 5 minutes and I was done with the adjustment and the retesting. A Beautifully designed and easy to set-up and use tool.

The preset angles are easy to locate and lock-in and the triangulation gives it a solid feel. Highly recommended. Very accurate right out of the box, would have bought it sooner if I had known how good it was. One thing that has to be improved on is the tape measure placement, it is just about useless. In the past years, I bought over 50 tools while setting up a shop in my basement: table saw, drill press, band saw, jointer, planer, dozens of pricey hand tools, multiple power tools, accessories, etc.

In retrospect, the worst tool I ever bought was a tenon jig from Delta. I am still in therapy for this. As for the best tool, it's definitely this miter gauge. Perfection is described as the point where nothing can be removed or added to an object without negatively affecting it's purpose. This is it. And then came this miter gauge straight from the gods themselves.

I open the pack, lay out the pieces, and surprise, it's all there. I read the instructions, and not only are they concise and clear, but they even afford the luxury of common sense that address the reader as a person, not a P. As I put this thing together, I am thinking: there has got to be a mistake, this makes so much sense, this is such a simple and efficient design my favorite is the hex screw for the miter slide adjustment , it's impossible!!

I micro-adjust the angle to a perfect 90 degree and, as I move the fence with the precision of a swiss watchmaker, I am overwhelmed with emotion. I secure the assembly. Then I reach for a 7 inches plank, position it on my table saw, switch on the blade, and I push, for better or for worse.

And it happen, as god is my witness, I produced two corners with such perfect square angle that I almost called Stockholm to let them know. And I think I cried a little bit, too. Also, try the Dow teflon lube the blue can to lubricate the miter slide on your table saw. It sets dry so it wont collect dust, and it last quite a bit. Thats what I use on my motorcycle chain too. Although a little pricy, it really makes accurate miters. I use it mostly Osborne Miter Gauge Instructions With for picture frames and the movable stop aids in getting the legs exactly right, even with angles already cut on one end.

Accuracy is dead-on, even with pieces that are deep enough that they hang over the front of the table when you start the cut. The grip-tape on the face keeps the workpiece from being pulled into the blade during the cut. I have a couple of miter gauges and wish I would have bought this one a few years ago when I first noticed it, it would have saved me some grief.

Converting my garage to a woodworking shop. Gives comfort in handling smaller pieces Osborne Miter Gauge Instructions Remove of wood especially when utilizing the dado. This miter gauge was very easy to set up. Well made. The gripping material that was included made it easy to hold the wood to the miter gauge, even at 45 degrees. I didn't have to use a "death grip" on the wood. I put the material on both sides of the adjustable extension to keep the wood flush with the gauge when extended on either the left or right side of the blade.

Beats more expensive miter tools. Easy to set up, change and use. You feel much safer and more accurate using this, and you therefore use it more. I was very impressed with this mitre guage straight out of the box. Only had to adjust the screw on the miter slot for a good fit and it was ready for use. It has a nice solid feel and on checking with a digital angle protractor, I couldn't fault it. The triangle concept really makes it robust.

Haven't tried any other guages but this one works very well. Used for General Woodworking. Once set up it seems to stay accurate.

Carving Kitchen Washington Dc 65 Cabinet Drawer Hinges Youtube Build Your Own Router Table Fence Snap On Mallet Hammer 70