Metal Lathe Pen Turning Tutorial | The International Association of Penturners

Making a pen lathe can be rewarding and fun to do as a hobby. They are simple to make with the right materials and know how. You can choose to keep them, sell them, or give them to people as a gift. This product is one of the easiest to make with a lathe. If you did not making pens on a lathe quote blanks that were pre-cut then you will need to cut them into two pieces. They are used for the top and bottom of the pen. They can be cut makng the band or table saw.

Be sure to cut them making pens on a lathe quote larger than the length specified. Mark the blank so the grain pattern can be matched easily when lahte the pen.

This is an important step to do so that no holes or gaps show where the fittings and blank meet. You can use a miter gauge with disc sander to square off the ends. If you are planning on making multiple pens, then store your blanks in a divided box. Drill slowly so the blank does not get ruined. To find the center of the blank, make an X corner to corner on the blank.

The center of the X marks the center of the blank where you need to drill. The pen kit will tell you pes size of the bit to use. Use the clamp to hold it in place while drilling. Once the drilling is completed, it is time to glue the brass tubes inside the blank. Read the provided instructions on the blank and tub specifics. Remove any tarnish that may be on the blank with sandpaper.

This also ensures that the glue mkaing bond properly. Hold the blank and put a couple of drops on the end. You will then turn the blank around to let makiny glue run making pens on a lathe quote the opposite end. The glue will also be spread out on the inside.

Take the tubes and put them in the blank. Now allow time to dry on a piece of wax paper. Look at the instructions for the pen kit to know what size bushing to use. On the mandrel, tighten the nut. Be sure to not tighten it too much. The mandrel now needs to be secured to the lathe.

By hand, you need to turn the blank and make sure they do not make contact with the lathe. Now, turn the lathe at the highest speed it can go. Be sure to use your safety equipment now that it is time to turn. When turning, be sure not to go too far. You can now use sand paper or a skew chisel to finish the blank.

Sand the pen lathe until it is smooth. You can now place a finish on the blank of your choosing. Some are makimg, and others are applied during the turning.

Checking with the directions on the pen kit, assemble the pen. We welcome your comments and suggestions. All information is provided "AS IS. All rights reserved. You may freely link kaking this site, and use it for non-commercial use subject to our terms of use. View our Privacy Policy making pens on a lathe quote. Toggle making pens on a lathe quote subscribe.

How to Make a Pen Lathe. Written by Doityourself Staff. What You'll Need. Drill bit. Drill press. Band or table saw. Disc sander. Bench vice or clamps. Pen kit. Wood blanks. Wax paper. Disc Sander vs Belt Sander. How to Replace Concrete Stair Treads. I'm doing some repairs on a year old house in the area. I've done a fa Read More. Metal lath and scratch coat question. General question about lath and scratch.

I am working on a hearth and will Mac vacom tablet, want for serial port on Amiga. I have an ancient Mac-wired Wacom tablet with pen, annd was wondering if it My wife got a little electric shock when she turned off the range hood this Related Posts How making pens on a lathe quote existing lathe and plaster exterior wall?

Hello, My home was built in The exterior is Stucco, lathe and plaste How to make a Straight line. Ceiling rock lath repair. I have a ceiling that made of "rock lath", a gypsum base, then a brown coat Replacing plaster and lath to drywall.

I have a brick house built in Pieces of making pens on a lathe quote ceiling upstairs fell and Popular Articles. Tips for Mounting Wood Turning Blanks on How to Make Wooden Napkin Rings. Basic Wood Turning Lathe Techniques. How to Make a Lathe Chuck Mount.

Taytools Pen Turning Lathe Mandrel Morse Taper MT1 Quick Adjust, Handles Blanks Up to 5 Inches, Overall Length 9 Inches. out of 5 stars $ $ Get it as soon as Thu, Mar FREE Shipping on orders over $25 shipped by Amazon. Only 2 left in stock - order soon. Apr 14,  · I also have a metal lathe and have turned one pen on it. The problem with Making Pens On A Lathe Quality turning pens on a metal lathe as I see it is that a metal lathe (if aligned correctly) will make nice straight cuts. A lot of the kits I've used require slight curves to them to look best.

Woodworking Bench Tools Online Small Cabinet Hinges 90