Set your drill bit collar to the correct depth. Kreg Jigs can help you drill what are known as pocket Kreg Pocket Tool Instructions 5g holes, which allow screws to be inserted at an angle. Follow kregjig on Instagram for the latest from Kreg! You kreg pocket tool instructions for make your solid-wood edging as wide as you want, and you can easily use dimensional boards. Align the pieces, then instructins glue on the mating ends.

Figure out the dimensions divider, shelf, or internal panel you need to create, and then cut it to size. Drill pocket holes along the ends or edges, as needed, to attach this piece into your box structure.

Align the panel and then attach it using pocket-hole screws. This clamp works great on corners. Whether you build shelves from solid wood or plywood, they tend to sag over time under the weight of their load. But you can also position the edging so it sticks up above the shelf to help hold items in place.

A good rule is to make the edging twice as wide as the thickness of your shelf. Or you can make your edging yourself by ripping boards to the width you need using the Adaptive Cutting System. Drill pocket holes in the underside of your shelf along the edge where you want to add the edging.

Attach the edging to your shelf using Kreg Pocket-Hole Screws. Of course, there are many more things you can do with your pocket-hole jig. Now, go get building! Check out our Projects and Plans page ideas, inspiration, and step-by-step instructions for your next project. Make 7 simple joints with your pocket-hole Kreg Tool Company K4 Pocket Hole System For jig. Flat joints This kind of joint is made by attaching two pieces side by side so that the faces remain flat and flush. Panels: By joining boards together edge-to-edge, you can create wide panels for things such as table tops, cutting boards, or even a workbench top.

Lay out your boards and mark them. TIP: Clamp your joints for best results To hold the faces of the boards flush as you assemble them, clamp across each joint as you drive in the screws.

Shelf edging: Whether you build shelves from solid wood or plywood, they tend to sag over time under the weight of their load. Related Topics How to select the correct pocket-hole screw.

Adaptive Cutting System: a new cutting solution. Learn the basics of building. Related Plans Easy, Elegant Bench. Knowing the exact thickness of the board will enable you to drill the pocket holes at just the right angle.

The difference of a fraction of an inch could potentially throw off your whole project. Set your drill bit collar to the correct depth. Line the pocket hole drill bit up with the specifications indicated on the base of the jig. The step the place on the bit where it narrows to a point should be even with the notch that corresponds to the thickness of your board.

Slide the depth collar to the appropriate height and tighten it using an Allen wrench. A special pocket hole drill bit should be included with your new Kreg Jig.

Change the placement of the jig. Using the same measurements, adjust the height of the jig to the appropriate position. To do this, loosen the thumbscrew on the back so that you can raise or lower guide hole piece freely.

Once the jig is where you want it, tighten the thumbscrew to secure it. Remember to reset Kreg Pocket Tool Instructions 00 the guide hole piece every time you drill a board of a different size. Secure the jig to the workbench. Clamp the jig down so that it will remain firmly in place.

Make sure the guide holes of the jig are facing toward you on the workbench. Part 2 of Clamp the wood into the jig. Place one end of the wooden board vertically against the clamp backing on the opposite side of the jig, then pull the lever to press the clamp tight against it. Fit the drill bit into the guide holes in the jig. The guide holes should be just large enough to comfortably accommodate the drill bit. Most standard Kreg Jig models will have at least three guide holes so that you can drill as many holes as needed to support the joint.

Should you need more pocket holes than your jig allows, you can make room for more by shifting the wood down in the clamp after drilling your first set. Drill the desired number of pocket holes. Pull back on the drill as you work to free the guide holes of loose wood chips.

Drill as many holes as you need to create a strong joint that will suit the purposes of your project, then turn the board around and repeat the process on the other end. Part 3 of Press the pieces of wood together to form a joint. Make sure the edges are evenly aligned. If you prefer, you can clamp the boards in place to make them easier to manage.

Glue the edges of the joint together for added security. Spread a thin layer of wood glue onto the edges of the boards where they connect. This will reinforce the joint even further and prevent the boards from coming apart as you fasten them. If you're using wood glue in addition to a conventional clamp, apply the glue before you align the edges of the boards. Drill the screws into place.

Drive the screws deep until they disappear inside the pocket hole. The pocket hole bit conveniently bores its own thread as it drills, so you should have no problem getting the screws to hold.

What more can we say? The name speaks for itself. This compact shelf will look great Kreg Pocket Tool Instructions in just about any room. Put your favorite plants on a pedestal. You can build a tall or short version to customize it for your space. This website uses first party and third party cookies to improve your experience and anonymously track site visits. By visiting this website, you opt-in to the use of cookies. A tool for every task.

Find the right pocket-hole screw Kreg screws come in many different lengths, finishes, and thread types. Find a Screw. Learn to make 7 simple wood joints Learn more.

Digital Tape Measure With Lcd Display Diy Woodworking Project Plans Yard