Open the door and power drill screws into the door-side of the hinge. Use self-centering drilling bit to drill the screwholes mxc a driver to attach install european cabinet door hinges mac screws into these holes. Step 8. By signing up, you agree to our Privacy Notice and European users agree to the data transfer policy. With a Clip-top Blumotion hinge, all you need to fine-tune the position of a cabinet door is a 2 Pozidriv screwdriver. Open the door and caabinet screws into the screw holes on the door.

Apply pressure against the drill to drive the bit into the door. Insert the hinge cups and drill wood screws into the screw holes. The hinge cup refers to the convex, cup-like part of the concealed hinge that goes inside of the bored hole in the door. Fit the cup of the hinge into the hole so the screwholes are flush against the surface of the cabinet door. Shim the door in place and measure the gap. Shim the door against the cabinet and use a ruler or tape measure to measure the small gap between the cabinet door and the cabinet surface.

Mark 2. Measure the distance from the edge at the front of the cabinet itself. Mark a line with a pencil that runs from the top of the cabinet down to the bottom so you can intersect it with your hinge measurements. Add the gap to the height and mark the top and bottom of the cabinet. Take your gap measurement and add it to 3. Then, measure that distance from the top and bottom of the cabinet and mark the locations with a pencil. When you make your marking, the 2 lines on your cabinet should intersect.

Align the mounting plate where the lines cross and drill them into place. Place the mounting plate at the location where both lines intersect and line it up so the screw holes are even. Use a power drill to drive screws into the screw holes to secure the plate in place. Then, attach the other mounting plate to the cabinet in the same way. Hook the hinges onto the mounting plates and snap them into place.

Press on the bars of the hinge to snap them into place on the mounting plates. Open and close the door to make sure the hinges work and the door is even. Method 2 of Choose a traditional hinge to add a stylistic detail to your cabinets.

Traditional hinges are mounted to the surface of the cabinet door and are visible, or partially visible when the door is closed.

There are a variety of traditional hinges including, butt hinges, flush hinges, and antique hinges, but they all fit onto your cabinets in a similar fashion. Look for traditional hinges at home improvement stores, hardware stores, and online. You could also look for ornate or decorative hinges at antique stores. Start by placing the hinges on the cabinet where you plan to install them, wrapped around the outer edge of the cabinet wall in the open position.

The hinges should sit flush against the outside and inside of the cabinet. The spacing needs to be even so the cabinet door fits correctly and opens and closes smoothly. Write down the measurements so you can duplicate them if you plan to install hinges on multiple cabinets and cabinet doors. Drive screws into the screw holes on the cabinet. Once the hinges are aligned, screw the cabinet-side of the hinge to the cabinet with a power drill.

Add a line of hot glue to the top of the hinges and place the door on top. Apply a line of hot glue to the top of the hinges and place the cabinet door on top of them. Open the door and drive screws into the screw holes on the door.

Use a power drill to drive screws into the screw holes to secure the hinges to the door. Include your email address to get a message when this question is answered. By using this service, some information may be shared with YouTube. Submit a Tip All tip submissions are carefully reviewed before being published. Related wikiHows How to. How to. More References 8.

About This Article. Co-authored by:. Co-authors: 4. Updated: April 2, Categories: Home Appliances. Thanks to all authors for creating a page that has been read 23, times.

Did this article help you? Yes No. Cookies make wikiHow better. By continuing to use our site, you agree to our cookie policy. For the best experience on our site, be sure to turn on Javascript in your browser. Here's a typical layout for a face frame overlay hinge. Most face frame hinge mounting plates have tabs that align the plate with the edge of the face frame. Either the edge of the cup hole or the center can be used as a reference for the vertical position of the mounting plate on the cabinet.

The fractional approximations given are perfectly adequate for the purpose of installing hinges. Once the center point of the hinge cup hole is transferred to the edge of the face frame, determining the topmost screw hole position is just a matter of measuring up 16mm for most European hinges. For frameless cabinets, the distance from the front edge of the cabinet to the screw holes can be measured, following the hinge instructions.

Hardwood Products Manufacturers Guide Jet 10 Inch Band Saw Blades Manual Jet 14 Bandsaw Vs Grizzly 14 Bandsaw Review Woodworking Shop Square Foot Free