Before beginning stir the topcoat well. This stain is fast drying and cleans easily with soap and water. Antiquing is a common technique used to give painted or stained woodwork an aged look. How Gel Coat Stain Fiberglass Doors Price do have time for staining, drying, sealing and drying again? Stacy Davis.

Moving across each side of the door from inside out, I built up thin coats until I had the depth of color I wanted. I ended up with six coats on each side I layered colors to match our existing woodwork. I found an exception. If you find grain that is not getting stained, rub or brush harder!

But also try moving a dark stain cross-grain just enough to deposit stain in the lowest grooves. I used a Spanish Oak almost black stain for grain emphasis and for overall darkening. If you are trying to match existing woodwork, try to bring some of the trim you are trying to match into your workspace. I laid down a golden oak base, then layered an Old Masters mahogany tone. When I compared to our trim, I discovered that my initial mahogany layer was tending a little too aubergine US: eggplant , so I buffed that layer down and used a redder version for subsequent coats.

Without the trim to place right up against the door, they would have looked the same to me and given me a mismatch. This all sounds fairly straightforward if time-consuming , but the tricky thing is avoiding tell-tale smudges.

The last thing you should do after each coat is to carefully examine each joint and panel to see if there are any smudges or lines left from your application or rubdown. Then leave the room, have a quick drink, and come back and look again while you still have some open time. More than once, I missed a smudge on first inspection, but taking a breath and coming back gives you fresh eyes. Smudges galore at the window plugs — this spot has been rubbed down a couple of layers with an eraser sponge prior to touch-up.

If you find you have some smudges or lines after everything has dried, freak not. I found recommendations online to use mineral spirits British: white spirit to rub down those areas so you can start over, but that turned out to be hard to do in real life.

That stain did NOT want to budge! I found that a nearly bone-dry eraser sponge very lightly applied is much easier and as effective. These are terrific and so are the generic versions.

Use your judgment given the number of coats remaining and the stain color the less you take off, the easier it is to match back up. Try to avoid this issue in the first place because feathering in can lead to more unevenness or smudging. As you can maybe tell, this project is a big pain in the neck! In addition, Gel Stain can be applied to non-wood surfaces, including metal, veneer and fiberglass, to give them a beautiful wood appearance.

Fiberglass is non-porous and won't absorb the stain the way a wood surface does. So, it's best to apply Gel Stain with a bristle brush.

Excess stain should be evened out with the brush - not wiped away with a rag. See application instructions above. Some woods, such as pine and maple, tend to absorb stains unevenly. The better the wood preparation, the better the final result. Looking for speed and convenience? Minwax Design Series washes, wood effects and waxes offer new options for bare wood and wood that's already stained. Combine the Minwax Design Series with other Minwax stains to produce on-trend looks, finishes and special effects.

For superior durability and long-lasting beauty, the choice is clear — protective clear finishes from Minwax! Where to Buy. Its unique non-drip formula makes application easy for vertical surfaces. Delivers uniform color evenly on wood and non-wood surfaces, such as metal, veneer, and fiberglass.

To darken the color, apply a second coat after hours. Recommended Uses: woodwork, furniture, doors, molding, trim, cabinets, accessories. Colors The colors shown are for reference purposes only. Getting Started? See How Simple! View More Videos. Old Masters uses only the finest ingredients to create the highest quality stains available today. Old Masters stains can be used to:.

Each Old Masters stain is uniquely formulated to fulfill different functions. Read the following descriptions to help you choose the right stain for your project. Penetrating Stain is recommended for use on unfinished, interior wood surfaces or surfaces in which the previous finish has been removed.

It is especially recommended for staining unfinished hardwoods, such as oak, ash, walnut, and mahogany. Wiping Stain can be used on a variety of surfaces, including unfinished wood, previously finished surfaces, fiberglass, metal, and composition surfaces. Especially recommended for woods such as pine, birch, maple, poplar, and cherry. Gel Stain is specifically formulated for use on nonporous surfaces, such as fiberglass, metal, and composition surfaces and is also suitable for wood applications.

It is especially recommended for woods such as pine, birch, maple, poplar, and cherry. Gel Stain is excellent for vertical surfaces.

Water-Based Wood Stain is recommended for use on bare, interior wood surfaces or surfaces from which the previous finish has been removed. This stain is fast drying and cleans easily with soap and water.

Use the following steps for general stain application on properly prepared wood surfaces. Stripping the finish is not always necessary to change the color of your woodworking projects. Start by thoroughly cleaning your project. Sand it lightly with a fine grit sandpaper and then remove the dust with a tack cloth. Using Old Masters Wiping Stain or Gel Stain , apply a thin coat to start and feather it with a dry, soft- tipped bristle brush.

Recoat your project with 2 to 3 coats of an Old Masters clear finish to protect the new, rich color. For closed-grain hardwoods, we recommend using Old Masters Wiping Stain , but instead of wiping off the excess stain as normally done, try brushing out the excess stain. This will give you a more uniform appearance and color intensity. Old Masters Gel Stain is specifically designed to adhere to fiberglass doors and plastic trim. Apply it directly to the fiberglass surface.

Wiping Stain also works well on these projects, especially as a second coat or intermixed with Gel Stain. For complete instructions on how to stain fiberglass doors, refer to our Fiberglass Doors Staining Guide. Old Masters offers a wide variety of products and tools used to create unique faux finishes. This section offers a brief overview of these techniques and various products and tools needed to complete each faux finish. Old Masters offers a complete wood graining system.

Kreg Stopper Youtube Woodturning Tools China Uk