Turning Project Plans | WOOD Magazine

In case of difficulty, this video is also posted on YouTube link and FaceBook cool wood turning projects online. I started turning this vase shortly after receiving it in a club wood raffle. It was still wet. It cool wood turning projects online to be perfect for a hollow form turning.

I rough turned the outside and hollowed it while still green. I weighed it periodically to assess how much moisture had been lost. Remounting a dry but warped project is always part of the challenge. In this case I had placed a scrap disk over Cool Woodworking Projects To Sell 100 the entry to the inside to limit air movement.

This now served as a trning while I recut a tenon on the base. Cool wood turning projects online this case I used a sanding pad to remove the last of the nub on the bottom. Then a turnihg holds the collet securely to the spindle. This works better than a Jacobs chuck in the spindle. In case of difficulty, this is also posted on YouTube link and FaceBook link.

For this vase, I wanted to have a lid. Not just pfojects lid but one that had an onlie connection. My Wood Turning Projects Beginner Online segmented vase was a perfect opportunity. If I prepared the vase right, I could hide magnets in a segmented ring. Besides being invisible, their power would also be invisible.

So, I embedded eight 6mm x 3mm ferrite magnets in the joint. A layer of segmented wood hids the magnets. While the wood reduces the power of the magnets, they are still strong enough that I can hold this vase upside down.

I used quite a few threaded wood faceplates as I needed to hold cool wood turning projects online rings from both tutning at times. My Live Tailstock Chuck Adapter from Penn State also came in very handy in aligning segmented rings to a faceplate and when parting a ring into two smaller rings.

In case of viewing difficulty, this is also posted on YouTube link and FaceBook link. In preparing for a remote demonstration, I projecte I went crazy with some inside out turnings. An inside out turning can be fascinating. For an inside out turning, staves are temporarily fastened together while a profile is cut.

Then each stave is rotated and permanently joined before turning another profile. The first turning is then on the inside while the second turning is outside. Usually an inside out turning uses cool wood turning projects online or four staves.

A two stave project is flat with an inner cavity. A four stave is more 3 dimensional with four cool wood turning projects online into the interior. Sometimes, another object is placed inside the final turning. A three stave inside out turning is a little more complex because the initial stock must be cut at a 60 degree angle. After that, the process is the same. However, a triple stave turning has larger windows into the interior.

I like the larger windows. While I was at it, I made two turnings with a captured sphere inside and one with an LED tea light cool wood turning projects online. In case of viewing difficulty, this video is also posted on YouTube link and FaceBook link.

Most often when preparing to make a segmented project, I have to prepare a detailed plan to know what size rings to make. However, not so in this project. I also speed glued the rings together.

It turns out that each ring does not have its glue fully cured before being glued to the next one. But first. I turned the exterior nearly to final shape with all rings assembled together on a threaded rod. Then I glued them all together in three sections, hollowed each section, then glued the final form together. It is 10 inches tall and 5 inches diameter. Segments total My steady rest from a couple of weeks ago also came in quite handy.

In cool wood turning projects online this video cannot display here, it is also posted on YouTube and FaceBook. I love turning green wood when I can get it. Ornamental pear is often called Bradford Pear. This wood came from a half section of that wood. I rough turned the bowl, sealed cool wood turning projects online and put it away.

Periodically, I weighed it and recorded the weight. That loss is typical in my experience for fresh green wood. In case of this video not playing correctly here, it is also posted on YouTube and FaceBook. A vase can be pretty. However, these vases are more dynamic. As you look at them the projectd has two profiles: a typical outer profile and an inner profile.

I started with eight segmented rings of walnut and nine segmented rings of maple. Each ring has eight segments. Each of these rings was sawn into projectw rings.

In addition, I made top and bottom rings for each vase. Total segment count is segments. The thinner walnut rings were stacked onto a mandrel and turned turninf the outer profile. The thinner maple rings were similarly turned for the inner profile.

Then ojline rings were glued to top and bottom rings to form the vase. Therefore, this process yields two similar vases. Final finish is walnut oil. Please see my video on splitting segmented rings. In case this video cannot be viewed here, it is also posted on YouTube and FaceBook. The design includes a spindle for the ring plus a tray at the base for other small items.

The shape of the dish keeps the small items spread out near the other edge of the dish portion. Pefect for small jewelry items. The wood is olive from Arizona. I had to fill portions with epoxy and brass power. The piece is finished proiects walnut oil. These are only about 4 to 5 cool wood turning projects online in diameter and about 4 to 5 inches tall. For the convenience of some, cool wood turning projects online video is also posted on YouTube and FaceBook.

Several years ago, I researched steady rests for my lathe. A steady rest resists lateral pressure that may push the wood out of alignment or even out of the chuck.

It works great on long spindles. After making my steady rest, I revised it so ckol I could bring the tool rest closer to the steady rest. The original steady rest and the wide banjo on my lathe forced each other to cool wood turning projects online further away.

A revised base solved that problem. A tricky knob box reduced the need for a wider base. The knob box enabled my steady to be adjustable at right angles to the turning axis. My revised steady has stood the test of time. I have not felt the need to change it again. There are minor improvements that could be made to make it prettier but would not change how it functions.

I have been asked about measured drawings. However, the steady rest should be customized for different cool wood turning projects online since axis height, bed gaps, bed thickness, bed width and turning styles all vary. In this video, I am showing the principles involved with my steady rest. Once you understand the principles, you can adapt it to your lathe and style.

I would appreciate hearing back what you have done to improve this design. For convenience or in case of problems, this post is also available on YouTube and FaceBook. Of course a couple were mine. But another that I will attempt to emulate was by Phil Irons.

5 Wood Turning Project Ideas For Beginners. The suggestion for beginners is to use wood that you may find on your property fallen from trees. Alternatively, you can practice with pine until you get the basics enough to work on some simple projects. So here are a few super simple beginner lathe projects you can start out with.

Steel City Mortiser For Sale 01 King Industrial Belt And Disc Sander Difference Router Login Page Aztech Build A Toyota Tacoma 2021 5d