The "Dust Cutter II" features an easy-to-mount Contractor Table Saw Dust Collection Inc nylon tooll that fits both contractor and cabinet style tablesaws. By TheWoodfather www. Dust collectors are essential and convenient for woodworkers. Its main function is to protect your fingers and limbs from accidentally contractor table saw dust collection tool contact with the blade when the tool is on. Any support is very much appreciated! I started cutting up 3mm MDF sheets to fit, I have lots of this left collectiln from an old project.

I can let it settle, then simply pull the drawer out and vacuum it up or slide it straight into a bin. I've had it in place for a month or so now, it has made a huge difference to the general cleanliness of the shop. Reply 5 years ago on Introduction. Ages ago, when I had a tablesaw, I fashioned a snorkel pickup for the shop vac that slung just below the sawblade's rear, where most of the debris is ejected.

It's far more effective to gather at the point of origin than to try and pickup from the base. If a vacuum is not an option, then this drawer design is a very good alternative. I now use a radial arm saw for all woodworking and metalworking cuts, so duct control is greatly simplified. The back of my saw doesn't seem to be a huge problem to be honest, though covering the hole would still be helpful. I have a plan to cover it, I just have to find out if the product I plan to use actually exists!

I have the same Oneida cyclone bolted to a 5 gallon bucket and man, it works. I also have one of their larger ones bolted to a 55 gallon drum and powered by a Harbor Freight dust collector blower and I have exactly the same results. I never have to clean out the filters. I use the smaller one with the shop vac for sanding and the larger one collects from my stationary tools. I did something very similar to my table saw. Well, yours looks a heck of a lot better than mine.

However, I took another step and attached my shop-vac to the bottom. Then I got super tired of emptying the shop-vac out seemingly, like, every 15 minutes! Plus, the filer would get all plugged up with the saw dust, etc. I spent a few days trying to put together a DIY cyclone filter thing, but in the end I picked up one of Contractor Table Saw Dust Collection Quest these Oneida things:.

I haven't had to open that shop vac for cleaning in over two years. Well, I do open it from time to time to check if it needed to be cleaned, but it hasn't needed it. I hope this doesn't seem like too much of a commercial I'll attach a picture of my shop-vac rig, I guess? Somehow, that makes this comment seem like less of a commercial in my mind. Hmm, maybe I should start working on another Instructable? But a little incident that I had one day kind of woke me up to a real problem.

My saw was having trouble getting through a piece of Elm and was smoking a bit. That was not unusual as anyone who has cut thick hardwood knows, sometimes it smokes. But then the smoke started getting really thick. And the air from the saw was fanning it into a nice blaze! Amazingly I had a scoop shovel and a nice size snowdrift outside the door. Notify me when back in stock Enter your email address to receive a notification when this item comes back in stock Submit Close.

If you use a tablesaw without a dust port; then you must have a look at this revolutionary dust collection system. Skip to the end of the images gallery. Skip to the beginning of the images gallery.

Questions and Answers. Product Reviews. Related Products Check items to add to the cart or select all. Large Dust Collection Separator. Router Table Dust Collector. Mini 2-Stage Cyclone Separator. The panels have rare-earth magnets embedded in them which give a strong connection to the saw but make it quick and easy to remove the panels. Click on the button below to download a free PDF plan for the back panels. The majority of the gaps around the saw should be closed in to help concentrate the suction to around the blade and help keep dust from escaping.

You don't want to fill every gap and make your saw air tight otherwise you will starve your dust collector of air and lessen your dust collection efficiency. I used upholstery foam that I had kicking around Contractor Table Saw Dust Collection Temperature the shop to cut to custom shapes and sizes to fit in around the blade tilt slot as well as the gaps between the saw top and cabinet. There are plenty of small Ridgid Table Saw Dust Collection System Unit gaps left like around the openings in the back panels and the hole and slot in the throat plate to supply air to the dust collector.

The idea here is to close in the extra gaps and openings to help direct the suction to where the blade is doing the cutting. The more air that is drawn in close to the blade the better the collection will be. The dust that is the hardest to effectively capture on the table saw is the dust that spits off the back of the blade. This dust flies into the air and spits back toward you making you look like you just walked through a sawdust storm. There are different commercially available overarm collectors available but I have designed my own shop-made version we all know that I love shop made efficiency solutions.

The dimensions of the overarm collector will be different for every saw but you can see how I made mine in the video below. The overarm uses a Bosch RA dust collection attachment meant for a router and you can purchase that through Amazon below. By using my affiliate links you're helping support the site and the DP Shop Talk channel which helps me help you by bringing you more content.

There is no extra cost to you but Amazon gives me a small commission from all items purchased. Any support is very much appreciated! If you have any comments or questions be sure to leave them in the comments box at the bottom of the page.

Lathe Tools Geelong Korea Letter Jiggle 2020