Create a Band Saw Milling Jig. To safely mill your log into dimensional lumber you’re going to need a milling jig. There are many variations of these jigs, but the simplest one is simply two sections of plywood connected together to form a 90 degree angle. A milling jig then either clamps or screws to the log. This will keep the log from rolling, rocking, or otherwise moving as it passes through the saw. Just as importantly it provides two flat surfaces to run along the the table and the fence of your band saw (or even table saw). This will allow you create two flat sides on the log. Plywood i. In this video I show how I made a Band saw Sled to cut log slices. My first attempt to make log slices didn't go so well, I ended up ruining a good Band saw. Yes, you can use a band saw to slice through a log of wood. That is with the correct blade and motor of course. Cast iron frames are the heaviest and sturdiest of them all, since they are built out of a solid, heavy chunk of molded iron with fewer welded joints or weak points.  There are a multitude of blade types out there, and some are engineered to do curvaceous cuts while the others are designed to rip through big hunks of hardwood. Some are so thin that you can cut precise dovetails or notches into the wooden board with them, while others are so wide that you will be better off sawing wooden logs with them. Some have steel teeth, so you can use them to slice through wood or softer metals such as aluminum, copper, tin, etc.

My saw vice seems woefully undersized for this job. This wasn't what I had in mind for using the ripping slot when I band saw for logs question the saw bench. The wood was pink and the shop smelled wonderful.

I found your site from an article someone posted to a question I asked on woodworkingtalk. You did it! At this point I guess most logs were ripped either by a huge two man pit saw or maybe everything was riven. You can find piles of one man cross-cut saws on ebay but no big rip saws. Do you like the champion tooth pattern? Or do you think that a plain tooth pattern would be better?

And would you recommend resharpening a crosscut saw into a rip saw like you did? Was band saw for logs question worth the effort? Fantastic article and fantastic website! Hi Ari, Sounds like a fun project. As you probably already read, the most difficult part was securing the log while sawing it. The saw itself worked really well.

I have my suspicion that the raker teeth did the majority of the work, so I would bet that just filing them to act like chisels would get you most of the way there. The problem is getting a file to work those teeth the ones that look like fish tails. Sure the pointed Band Saw Blades For Cutting Logs Work teeth did some of the work, but band saw for logs question angle of them is all off….

The shallow angle also helped make sure the saw was tracking Horizontal Band Saw For Logs Free well along the length of the log not perfect, but use-able. If Band saw for logs question was band saw for logs question the mood to experiment, and also wanted to still be able to use the saw for crosscuts, I would just file the raker teeth for rip and leave the others shaped for crosscut.

After a minute or two of sawing you would know whether it was enough or whether you needed to reshape the others. Incidentally, the filing on the acute angle teeth and grinding on the rakers all had the same geometry for me it was all done at a right angle to the saw blade filing straight across basically what I was going was removing all the fleam from each tooth.

Also, there is no need to remove all the fleam from the entire tooth, just the tip is all that is needed. My only other recommendation, wear ear protection. Those long teeth make a lot of noise when you run a file across them. I hope this helps. Home About Shop Reference.

Timber Frame Tools Timberframing on a small scale and other woodworking tales. Woodworking Topics architectural salvage 1 black smithing 1 books 3 boxes 1 furniture 20 gazebo 22 hardware 1 household 9 joinery 2 natural timbers 10 news 3 outdoor furniture 6 safety 1 siding 1 techniques 19 timber frame 28 tool history 7 tools 53 Uncategorized 3 Wood Fun 7. While doing the preparation for building a cedar band saw for logs question chaise lounge, I had collected several old fallen red band saw for logs question logs from the forest surrounding our home.

It seemed that one of the logs turned out to be more than my bandsaw could handle 8. The log was close to 14" in diameter. It was too good a source to waste. A log this size could provide all the wood I needed for the slats So I ran through my options for making it smaller. None of them seemed appropriate By ari gold on March 26, at pm.

Hi there, I found your site from an article someone posted to a question I asked on woodworkingtalk. Thanks a bunch! By swirt on March 27, at am.

As for power, my bandsaw has 12" of exposed blade and 14" side clearance to the column, is 1 HP and does fine with hardwood logs up to Band Saw Blade For Logs Js 12" high, although the feed rate is very slow (I'd guess approx. 1/8 to 1/4" in 10 seconds). There are other tricks to resawing so watch some videos and/or get a good bandsaw book to get more insights. Log Band Saw / Headrig, E. Gillet TO Manufacturer: E. Gillet Log Band Saw / Headrig, brand E. Gillet, model TO , with flywheels xmm, used. The machine is available for sale at the current condition or after a complete repair. The company selling this machine. Jun 15,  · While doing the preparation for building a cedar double chaise lounge, I had collected several old fallen red cedar logs from the forest surrounding our home. It seemed that one of the logs turned out to be more than my bandsaw could handle (" re-saw clearance). The log was close to 14" in diameter. It was too good a source to waste.

Woodworking Plans Console Table Used Crafts To Do With Wood Muscle Woodworking Plans Extending Dining Table Inc