Unfortunately this is out of our control but we will continue to ensure orders are despatched as quickly as possible. Knife Edge — Custom Cktting. Gullet Depth - The distance from the tooth tip to the bottom of the gullet. The carbide tipped tooth has carbide tips welded to a high strength alloy back. Find by Length. Find by Machine.

Unfortunately this is out of our control but we will continue to ensure orders are despatched as quickly as possible.

Manufactured from a single piece of high carbon steel with individually hardened tooth tips More fatigue resistant than carbon hard back Suitable for cutting: Aluminium Non-ferrous metals Low alloy steel Wood Plywood Composition board Cork Plastic 4, 6 and 10tpi tend to be used for cutting wood, plastic or non ferrous metals. Bimetal Bandsaw Blades Bimetal blades are metal cutting blades.

Manufactured from 2 metals — M42 tool steel is welded via an electron beam to a flexible backer They typically last times as long as a carbon blade flexback and hardback Suitable for cutting: Aluminium Brass Bronze Steel Titanium Stainless steel.

Reviews There are no reviews yet. About Us. Bandsaw Blades. Wood Cutting. These band saw blades produce a thin kerf and can make remarkably tight turns. Welds are re-tempered for superior strength at the weld. The weld on these blades is warranted. Please order carefully! You will be responsible for shipping charges on exchanges due to incorrect ordering.

In stock lengths available: 80", 82", Custom sizes are available. The rate is usually measured in feet per minute fpm or meters per minute mpm. Measured in square inches per minute. As with a bi-metal blade design, there are advantages to differing tooth constructions. The carbide tipped tooth has carbide tips welded to a high strength alloy back.

This results in a longer lasting, smoother cutting blade. Variable Positive - Variable tooth spacing and gullet capacity of this design reduces noise and vibration, while allowing faster cutting rates, long blade life and smooth cuts.

Variable - A design with benefits similar to the variable positive form for use at slower cutting rates. Standard - A good general purpose blade design for a wide range of applications. Skip - The wide gullet design makes this blade suited for non-metallic applications such as wood, cork, plastics and composition materials. Hook - Similar in design to the Skip form, this high raker blade can be used for materials which produce a discontinuous chip such as cast iron , as well as for non-metallic materials.

The number of teeth and the angle at which they are offset is referred to as "tooth set. Modified Raker: 5 or 7 tooth sequence with a uniform set angle for greater cutting efficiency and smoother surface finish Left, Right, Left, Right, Straight. The order of set teeth can vary by product. Vari-Raker: The tooth sequence is dependent on the tooth pitch and product family. Typically Vari-Raker set provides quiet, efficient cutting and a smooth finish with less burr.

Alternate: Every tooth is set in an alternating sequence. Used for quick removal of material when finish is not critical. Wavy: Groups of teeth set to each side within the overall set pattern. The teeth have varying amounts of set in a controlled pattern. Wavy set is typically used with fine pitch products to reduce noise, vibration and burr when cutting thin, interrupted applications.

The teeth have varying set magnitudes and set angles, providing for quieter operation with reduced vibration. Vari-Set is efficient for difficult-tocut materials and larger cross sections. Single Level Set: The blade geometry has a single tooth height dimension. Setting this geometry requires bending each tooth at the same position with the same amount of bend on each tooth.

Dual Level Set: This blade geometry has variable tooth height dimensions. Setting this product requires bending each tooth to variable heights and set magnitudes in order to achieve multiple cutting planes.

The number of teeth per inch TPI is important in obtaining the finish desired and the proper feed rate. A coarse tooth blade 2, 3 TPI should be used for re-sawing wood and cutting thicker stock up to 8" thick. The thickness of a bandsaw blade is determined by the thickness of the blade body. Bandsaw blades vary in thickness. Make sure that you select a blade of proper thickness. The continual flexing of the blade causes metal fatigue and failure of the blade.

Storing Wood For Turning On Fine Woodworking Toy Box Grizzly Woodworking Dust Collection Systems Malaysia