Read woodworker's blade reviews posted in our Bandsaw Blade Review section. Norton Publishing Wall Lenk Co. My Account. The Resaw King looks more like a table saw blade with its C8 carbide 111 bandsaw blades rikon teeth that are individually brazed and ground to perfection on a stress crack resistant Bqndsaw silicon steel backing. I have only used about 2 dz. Filters: Blade Width Clear Selection. Laguna - ResawKing Bandsaw Blade " x.

Laguna - Resaw King Bandsaw Blade Laguna - Resaw King Bandsaw Blade " x 1. Laguna Rikon Bandsaw Blades Canada Online - Resaw King Bandsaw Blade " x. Laguna - " x 1" Resaw King Blade. Laguna - Resaw King Bandsaw Blade 1" x Normal bandsaw blades use a hooked tooth design, with a set on each tooth that creates a larger kerf and leaves a rough cut.

The Resaw King looks more like a table saw blade with its C8 carbide tipped teeth that are individually brazed and ground to perfection on a stress crack resistant Swedish silicon steel backing. All blades feature a. If purchased at a Woodcraft Store, please return the item directly to the store where your purchase was made. New woodworking machines sold by Laguna Tools carry a two-year warranty effective from the date of shipping.

Laguna bandsaw blades' welds are Rikon 10 Bandsaw Blades System backed by their 1-yr manufacturer's warranty. Machines sold through dealers must be registered with Laguna Tools within 30 days of purchase to be covered by this warranty. Laguna Tools will repair or replace, without charge, any parts determined by Laguna Tools, Inc. It may cost a lot more than other brands but it is well worth it in time and stress. The blade is great and expensive.

But she "Don't" like Hickory!!! So I'm thinking any very hard dry wood will be a problem. Yes the band saw and blade are properly tuned. And yes was very slow feed rate had to be used A great blade worth the cost. I have had mixed results with various blades in re-sawing woods for my guitars and ukuleles.

That is all I needed to convince myself I had found the blade I always wanted. I almost exclusively use "exotic" species, Rosewoods, ebony, bubinga, etc. Bandsaw blades don't last long with these materials, and often left a rough surface which required hours of work with scrapers and sandpaper to polish smooth again. I ended up wasting a fair amount of these expensive and rare woods just to smooth the surface.

No more. This blade cuts through all woods like butter with an incredibly smooth surface. Was able to rough out a cane handle of snakewood very easily. Apparently it can also be resharpened several times. What a smooth cut! This thing glides through 12" thick material easily. Used on a powerful saw with great Carter guides all I need to do is sand the piece after re-sawing. Truly amazing. Purchased for my Rikon 14" bandsaw my saw is a little underpowered to see if it could help. Tooth angles and gullet symmetries, combined with a unique set pattern, create a blade that is everything a wood-cutting blade was meant to be.

The round design of the gullet eliminates any work hardening zones. Couple that with the special 6. High silicon, low carbide steel Ideal for resawing thick stock Runs cooler and lasts longer Runs under low tension which requires less horsepower Thin kerf. Yes, they're a little more expensive but they outlast and out perform any other blade that I've used. Been buying them for years and only had one problem and "Woodcraft" quickly did an exchange for me. Probably the only blade that I'll ever use.

I've used many different widths and TPI configurations and my opinion of all of them is the same. Top of the line product! Put it on and checked for resaw straightness and it was dead on.

Once finally on, and engaging lever, the blade was then over-tensioned and couldn't be tracked on the tires, it just wanted to move off one edge or the other and was unhappy near the center of the tires.

This is all with the coil spring tensioner completely loose. Others report blade lengths too short or too long and corresponding issues with that.

The blades would work well if the correct length. It wouldn't tension according to the tension scale on the bandsaw. I thought my tensioning mechanism on the saw was faulty. I called Rikon Tech Support, complaining that my tensioning mechanism had ceased to work.

The Tech Rep asked the make of the blade and I told him it is a Timber Wolf and he told me that was the problem. So it cannot be tensioned according to the tension scale. It has to be tensioned by feel. It's a great blade, but buyers should be aware that they cannot tension it according to the bandsaw scale, only by the deflection method. Find a Store. My Account. My Cart.

Triton Tra001 Router Table 10 Sawstop Model Cns175