Traditional cut nails can be made from pretty soft steel, especially the useful cut headless brads. About Us info philadelphiawoodworks. Sliding table saws The SCM joinery machines are the products of continuing in-house development complementing the sum of the finest skills and know-how. The large flat tenon cheeks and woodshop and joinery company walls need to be flat, Woodshop Supplies Woodworking Supply Company 5g smooth and parallel, joinegy shoulders have to line woodshop and joinery company. A mixture of general-purpose epoxy and fine sanding dust creates a rock-hard fill for knot voids. I will pull every drawer out if allowedstick my head in a carcase and send my fingers probing into the darkest voids. If you consult the 19th and early 20th century texts, they state that tenons should be one-third the thickness of your stock.

Some epoxy pastes have the consistency of chocolate pudding. The two parts can be stirred together in a tin or jar using a spoon. Other putties are squeezed from tubes and mixed and applied with a putty knife. Most problems with epoxy are caused by improper resin-to-hardener ratio or insufficient mixing. Note the all-critical working time, combine the two parts thoroughly, and prepare only as much as you can use at a time. If adding sanding dust or other thickeners, stir them into the mix afterward.

If a batch starts to tack up or cure in its mixing container, toss it. Measure small amounts using twin containers of the appropriate size.

Whatever the epoxy used, a strong connection depends on a snug fit, so cut your joints as carefully as you would for using any kind of glue. Yes, epoxy will fill gaps, but a gapped joint will be weaker than a well-fitted joint. Clamp the assembly just tight enough to pull the pieces together. Undue pressure may squeeze out the epoxy, starving the joint.

Leave the assembly clamped up for 24 hours. That said, quick-set epoxy does have its benefits. I use it in the finish room to fill small cracks and dings that show up at the last-minute. A mixture of general-purpose epoxy and fine sanding dust creates a rock-hard fill for knot voids. The damage at the tip of this plywood template is easily fixed using epoxy putty like JB Weld.

I treat cracks with general-purpose epoxy for a clear, tough fill that blends in under any surface finish see opening photo. For knotholes, I mix fine sanding dust and epoxy for a quick build and color match to the surrounding area. If a crack or knothole extends through a board or off its edge, mask off one face or the edge with duct tape as shown in Photo E.

If it keeps seeping in, let it cure awhile before applying more. Several applications may be required. Seal the edges of a knothole with general-purpose epoxy. Epoxy putty can be a quick-fix for damaged templates and jigs.

Mix equal amounts of resin and hardener together, and then push a glob of the material into place to repair wood or metal Photo G. Shape it after it cures.

My work sometimes includes restoration of partially rotted windows, doors, and other architectural elements. This water-thin epoxy is formulated to permeate and harden fragile, punky wood.

To use it, clean away any loose material from the damaged area and then pour the epoxy onto the surface, spreading it as necessary with a brush Photo H. When it comes to bonding dissimilar materials, epoxy reigns supreme. Annoyed by a loose-handled hammer?

No problem. Just drip some epoxy into the head Photo I. Dissatisfied with your stock turning tool handles? Turn new ones and attach them with epoxy. Uncured epoxy can be cleaned up with denatured alcohol. Fully cured epoxy can be planed, jointed, sawn, and sanded without a problem, although it is as hard as knots on blades. I generally feed epoxy-filled boards through my thickness sander and then finish up with a random-orbit sander.

Excess can also easily be removed with a cabinet scraper Photo J. Stephen Metz has been working wood professionally since You must be logged in to write a comment. Log In.

Find a Store. My Account. My Cart. Go to Home Page. Mobile Navigation. Same Day Shipping Find a Store. Ash has straight, coarse, open-pored grain of even texture. It also exhibits a pronounced difference between latewood and earlywood so matching boards requires care.

For most woodworking, the lighter-colored sapwood takes preference. Brown ash is darker, and presents a challenge when mixing with white ash in a project. White ash closely matches red oak in density and hardness. However, it burns more readily from dull cutting edges or a slow feed rate.

These marks are hard to sand off. Jointing, ripping, routing. Take shallow passes with a router to avoid burning. And always use a backing board with end-grain and cross-grain passes to avoid tear-out. All adhesives work well with white ash. All topcoat finishes work well on the wood, but keep in mind that under a clear finish, white ash yellows with age much like sugar maple.

Ever since the discovery in Michigan of the Asian emerald ash borer EAB in , the invasive beetle has killed more than 40 million ash trees from the Midwest to the Mid-Atlantic States and southern Canada.

At present, little can be done on a large scale except to locate infested areas, quarantine them, and destroy dying and dead trees. Quick View. Add to Cart. View Details. Woodcraft Woodshop - Ash 2. You must be logged in to write a comment. Log In. Find a Store. My Account. My Cart. Go to Home Page. Mobile Navigation. Same Day Shipping Find a Store. Search Go. Topics Cabinetry. Choosing Hardware. Dust Collection.

Friends of Woodcraft. Getting Started with Woodworking. Make Something. Pen Kit Reference Chart. Press Releases. Resin Casting.

Carpenter Tool Starter Kit 900 Best Raps In Pop Songs