Parallel clamp comparison these are extremely useful, at times, the product is quite costly. Comes with Improved operating jaw design. Weight: 3. Bora T Set. But we like it for clamping jigs to a workbench or tablesaw rip fence, and for light clamping of small boxes and assemblies.

We decided to sort them out in a head-to-head test. For each make, we tested 24" models and either a 48" or 50" version. The ability of the jaws to remain parallel under pressure separates these clamps from other styles.

To test this, we clamped equal-length 2x6s on edge in each set of clamps, and then measured the distance at three places between the jaws: at the bar, in the center, and at the tip.

Among the longer 48" and 50" clamps, only one remained parallel. So what to make of it? We also tested a few other types of clamps one-handed bar clamps, pipe clamps, and aluminum bar clamps and found their jaws canted more than the parallel-clamp jaws. All of the clamps have a fixed jaw at one end of the bar and a sliding jaw that travels along the bar.

On most models, that jaw often slides uncontrollably down the bar, crashing into the fixed jaw when held vertically. One model, though, has a finger trigger below the handle that engages the bar reliably, with no backsliding when tightening the jaw. Half of the clamps use setscrews to engage the serrations on the top and bottom of the bar while you tighten the handle.

However, all four Parallel Clamp Zinc crept backward more than half the time as we applied force to the assembly. Despite the advantages some clamps have over others in engaging the bar, ultimately they all were able to pull together everything we tried in our tests.

We were able to double the clamping force in this manner compared to using the handle in its inline setup. Two clamps, the Lee Valley Ehoma and the Yost K—virtually identical except for color and branding—have handle systems that helps you crank up the force, as shown above. You can also gain added leverage with the Bessey K Body Revo clamps, shown below.

These methods prove helpful for anyone with limited hand strength. Gain clamping force with the Bessey K Body Revo clamps by inserting a 6mm hex wrench into the socket in the handle end and cranking it. Jaw sleeves help prevent workpiece marring and provide a more glue-resistant surface compared to the actual jaws.

You can replace these or remove them for cleaning. With each clamp, the tail jaw is fixed to the bar, while the other jaw slides the length of the bar. The Bessey K Body models above and Jet below work best in this regard. All three have thick, sturdy bars with serrated top edges that the sliding jaws engage without backsliding when positioned against a workpiece or assembly.

The Irwin and Yost K clamp bars lack serrations, and the jaws grip easily enough, but over time problems can arise. To keep the sliding jaw from dragging on the workbench, you can reposition the foot on the Jet and Irwin clamps, helpful when the clamp is longer than your worksurface. A parallel clamp for the lighter side.

Although we were able to generate an average of nearly pounds of force with the UniKlamp, its jaws and bar flex too much for use with flat-panel glue-ups. But we like it for clamping jigs to a workbench or tablesaw rip fence, and for light clamping of small boxes and assemblies. Clamp down on your budget and spring for the leader As we said earlier, there were no duds in this group, but one clamp rose to the top: the Bessey K Body Revo.

It earns Top Tool honors. Steel alloy rail is there for safe, secure and slip-proof clamping. It has spreader to meet your needs. Rapid action jaw opening and closing-simply. Screw travels really fast ensuring flawless clamping. Besides comfortable gripping can be experienced as it has ergonomic designed 2 component molded soft-grip handle.

Comparatively heavy- you may face difficulties to move these clamps. Not suitable for giant workpieces as it only has a inch rail option. This makes all the Jet Parallel Clamp Warranty difference and adds a heck of a lot of versatility.

Though corner clamps also a nice option to make a corner joint. Another rationality for that is the bewildering lbs of clamping pressure.

The clamping pressure alone says how much of Jet Parallel Clamp Framing Kit heavy-duty clamps that this is going to be. Apparently, the clamp having a Resin body prevents glue adhesion.

I need not say how handy those features gonna be. Having your glue stuck to the clamp is a gruesome experience. So, after a while, this clamp might just turn out to be like one of those regular everyday clamp having glue stuck to it. This way the metal of the clamp degrades overtime. Jet inch is a sturdy inch clamp ideal for both clamping and spreading.

If you want to increase the length of the rail, you can! Non-marring composite resin jaw faces ensure safe degree clamping. At the same time, the movable rail stand and end stop will ensure that you will get the perfect measuring.

The best thing is that it is very easy to adjust to the desired point. On the other hand, the head will stay put, it will be like that until you squeeze the trigger. Screw handle turns without binding which gives you a hassle-free smooth experience. The grip of the handle is impressive. Moreover, the reversible clamping will convert clamp to a spreader that will not only make the whole tasks easier but also be a time saver.

After all, it is a very good clamp with perfect size. Jet provides a limited lifetime warranty. It means the manufacturer is confident enough about its product. The built quality is good and reliable materials are used. Some users have experienced that the screw slips when they tried to tighten it. Some had reported that the screw sometimes does not slide. If you work with workpieces of different sizes and want perfect clamps for all, then the Bora Parallel Jaw woodworking clamp is here.

It is available in 5 different rail lengths! Jaws are perfectly parallel which ensures degree clamping. Bora assures rock-solid clamping by designing perfect parallel jaws. The special design ensures that the jaw will be in place even while winding the clamps, that not only ensure perfection but also increase the safety.

Besides, gripping quality is out of the level having on both sides and also at the top-notch handles. There will be no chance to be slipped away from your hand even at tough conditions. The rail is something eye-catching.

End stops are there to ensure safety and to help to increase the rail-length. Screw travels faster than others ensuring fast clamping.

Some users experienced that the clamps are not perfectly parallel. Some had questioned its poor design as they experienced that the jaw is not in position rather 8 to 10 degrees twisted. A: Actually the parallel clamps are meant for woodworking purposes.

You can use C-clamps instead. A: YES, you can! The jaws can hold the panels Bessey Parallel Clamps Home Depot 50 during glue-ups to serve your purpose.

Parallel clamps are the heart of a woodshop. Manufacturers make parallel clamps for different purpose clamping. Some are really good for holding a heavy load, some are magnificent for clamping giant-sized workpieces, while others are for a better gripping performance.

If you work with huge workpieces, then Jet Inch Parallel Clamp is a better option for you. Bora Parallel Jaw Woodworking Clamp comes in different sizes. If you want similar clamps for all of your projects, then these should be the best parallel clamps for you. Pick up your tools according to your needs; nothing else.

Fine Woodworking Issue 279 Pdf Outlook Pocket Hole Jig Build Your Own Games Learn Woodworking Near Me Free