Marking Knives: Stuff They Never Teach You | Popular Woodworking Magazine

When making marks on wood, nothing beats a marking knife when precision is important. This simple knife was made from an old worn out file with rudimentary tools. If you have ever wanted to make a knife but don't have marking knife tool zero metal working tools, this project is for you.

Marking knife tool zero order to make the file workable, it needs to be annealed. This will make it less tough and easily shaped. To anneal the file, turn on the map gas torch and heat it until it loses its magnetism. I screwed a magnet to a long stick to keep my hands far away from the hot temperatures. Let the file cool down on it's own. Marking knife tool zero you have some, placing the file in marking knife tool zero pile of sand will help it cool down slowly.

Clamp the file in a vice and shape it using a hacksaw or angle grinder. Once the rough shape is achieved, refine it using a strip sander. Cut a 30 degree angle on a piece of scrap wood and clamp it to the strip sander. This will act as a guide for the bevel of the knife. Slowly drag marking knife tool zero blade of the knife over the Marking Knife Total Tools Easy guide until the blade is almost sharp.

Do not sharpen it at this point. The bevel needs to be on the more aggressive side of the file. The other side will need to be ground flat to ensure a sharp blade. Mark pin hole locations in the knife blank marking knife tool zero a center punch.

Be sure to clamp the blade in place. Do not hold it by hand. Using a brad point drill, mark the locations of the pins in the scales. Drill corresponding holes in the scales. With the pins in place, trace the tang on the inside of the scales. Remove the excess wood of the scales. To harden the blade, it needs to be heated just past the point when it loses its ability to be attracted to a magnet.

Once heated to this point, quench it in oil. I used canola oil as it doesn't smell bad compared to other oils used for hardening steel. If the entire Marking Knife Tool Definition Yes blade and tang were heat treated, remove the scale before tempering. Since only the marking knife tool zero portion of this knife was hardened, I skipped removing the scale at marking knife tool zero time.

Removing the scale will allow you to see the color of the blade after tempering. Heat the blade in an oven to degrees F for an hour and a half to two hours.

I used a toaster oven I have the the garage, but any oven will do. Once heated, turn the oven off and allow it to cool until you can handle it by hand. It should be a pale yellow color. Once tempered, remove the scale from the blade.

I used a set of whetstones to hone and sharpen the blade. Wrap the blade in painters tape. This will do two things, mask off the portion of the blade that shouldn't get epoxy on it, and keep you from getting cut. Once wrapped, place the scales on the tang.

Cut the painters tape along the edge of the scale. Remove the excess tape and apply ample amount of epoxy to the tang.

Attach the scales and pins to the tang. Apply sufficient even pressure on the scales using spring clamps. Let dry. Once the epoxy is dry, cut off the excess pins. Shape marking knife tool zero handle until it feels comfortable in the hand. Once the handle is comfortable, sand with increasingly fine sandpaper.

Once finished, admire your marking knife. No new tool is complete marking knife tool zero it has a location in the shop. Make yourself a holder and attach it to your Tool Wall. You have made something that will serve you well for years to come. Keep it sharp and get making! I'm happy with my shaping. Since I didn't anneal, I did the bulk of it with an angle grinder then finished with a belt sander.

It won't be getting a wooden handle. Now Marking knife tool zero need to find a good heart source and was thinking of setting up a charcoal forge marking knife tool zero sure there's an instructable out there. Do you folks think that would work for hardening and temporing? Reply 2 years ago. Hardenting, it should work great! I don't think you will be able to keep it at a low steady temperature for long enough to temper it however.

Question 2 years ago on Step 6. Answer 2 years ago. This is marking knife tool zero. The steps on hobby-shop annealment and hardening are worth the time just marking knife tool zero themselves. Question 3 years ago on Step 9.

You initially heated the file before shaping it enough to lose its magnetic properties. You then re-heat it at a later step to again lose its magnetic marking knife tool zero. Did they come back when cooled?

Please explain. Answer 3 years ago. Yes, magnetism will return once cooled. Carbon steel loses its magnetic properties around degrees F which is around the temperature you need for annealing and hardening the steel.

I have been hoarding old files for some time now. I pick them up at yard sales, etc. I've wanted to make a knife like this for some time, but I was not sure exactly what I was looking for in a knife, and your knife has given me some inspiration. I like the torch holder you have there, so now I have to make one tool to create another tool.

Thanks for posting this up, I really like it. Reply 3 years ago. These are the stones I purchased. I then popped them off the plastic stand and made my own holder for them. Question 3 years ago on Step This looks great, I may have to give it a go some time.

I have a whole load of old files I inherited. Is the steel used for making files particularly well-suited to this, after the heat treatments you describe? Introduction: Marking Knife From File.

By tomatoskins tomatoskins Follow. More by the author:. About: My name is Troy. I'm a Mechatronics and Aerospace Engineer. More About tomatoskins ». Attachments knife. PDF Download. Participated in the Trash marking knife tool zero Treasure View Contest. Did you make this project? Share it with us! I Made It! Reply Upvote. Yes good point.

Well I suppose I can use the oven in the kitchen to temper.

Marking Gauge. Both marking methods reflect thoughtful design. The wheel-knife Marking Knife Tool Game registers perfectly at the zero point of the engraved scale. A second knife and four spacers are included, allowing you to lay down two perfectly parallel lines at the same time. Narex Thin Blade Dual Double Bevel Striking Marking Knife () Narex. $ USD. This marking/striking knife is made by Narex of the Czech Republic. Blade is made from Mn-V steel and heat treated to HRc Handle is of European View full details. $ USD. Sale. Nov 02,  · And finding a good marking knife. The drill bit hunt is still on, but I have finally got on top of the iron dagger. My favourite knife for many years was a bit of old hacksaw blade, sharpened to a spear like point, so it could be used right or left-handed. The handle was made of tape and rag.

Woodworking Countersink 60 Marking Knife Vs Exacto Exactos Wood Workshop Hire Perth Zip Code Wood Router Table Fence Zero