Learn More. Regards Oilbert Texas. Feb 20, PST. Pic 3 Shows the angle gauge. The clamp plate is CNC punched and formed heavy gauge steel with multiple clamp position holes. Pic 1 The front of the FMT, showing the fence which is instrumental in being able to proceed from one board to the next lrigh re-entering.

Cutting compound mortises is doable with a little effort. Set guidance pins mean that setting cuts at less than 75mm total cut means that an ancillary method must be used. Differences between the two systems. More set up time is required for the FMT and it is fixed to the bench while the Domino requires little set time and is mobile. The Domino can perform other functions apart from straight mortise digging. Because of its method of operation along with mobility, long trenches can be achieved as well.

The FMT can provide mitred and compound mitred mortises and tenons easily see below and is not limited to a max of 10 and minimum of 5mm cuts. By using a different combination of bits for making the mortises and tenons and by using very small machine bits, it is possible to put a mortise and accompanying tenon into a matchstick.

I have been told this also applies to making wider mortises than12mm, but I have never tried it. The Domino is a self contained unit with a set value of variables for each cut. The FMT uses both jig and router. Each has a separate set of variables which may affect the cut and fit. The FMT has real difficulty with this and works best on square timber. I hope this is what you wanted Lou and I'm sure there are people just waiting to respond. In fact I hope so. Remember this is my view of the world, most likely the rest of the world has a contrary collective view.

I have attached some pics to show the FMT. Also I want to explain one particular case where the Domino was no use to me, though that may have changed over the last 12 months. I needed to join side rails to the front and back legs of 8 chairs. On measuring up the domino 8x40 it became apparent that the end of the domino would be about 5mm sorry for the mixed measurements from the side edge of the front leg. No problem I thought, I'll bed it deeper into the rail. No, not going to work either.

In the end I dominoed straight tenons into the leg and cut mm tenons on a 9 degree angle using the FMT. After about 5 minutes of set up, I produced 16 rails with two 9 degree tenons one pointing each way on each leg tenons in minutes and had only to mark the centre for cutting Leigh Fmt Mortise Tenon Jig Model on the first rail. Pic 1 The front of the FMT, showing the fence which is instrumental in being able to proceed from one board to the next without re-entering.

Pic 2 Shows the top with the extendable Leigh Fmt Mortise Tenon Jig Key centre cross hatch and the front and side stop sets which prevent the table moving during cutting. Pic 3 Shows the angle gauge. Combining a change in angle on the front fence with a change in angle here gives a compound mortise or tenon. Pic 4 Shows one of the 9 degree rails I mentioned earlier. Festool USA does not pre-approve the contents of this website nor endorse the application or use of any Festool product in any way other than in the manner described in the Festool Instruction Manual.

Although Festool strives for accuracy in the website material, the website may contain inaccuracies. Festool makes no representations about the accuracy, reliability, completeness Leigh Fmt Mortise Tenon Jig Nat or timeliness of the material on this website or about the results to be obtained from using the website.

Festool and its affiliates cannot be responsible for improper postings or your reliance on the website's material. It can be done right; it should be done right; and those of us who want it done right ought to be prepared to pay. Value given appears to at least match price paid. Congratulations to Leigh for giving honest value for price!

At first glance the product may seem a bit complicated and time consuming for setup - but simply follow the simple guidelines for learning to use the jig 2 hours start to finish - and from then on, creating quIck and perfect joints is a joy. Find a Store. My Account. My Cart. Go to Home Page. Mobile Navigation. Same Day Shipping Find a Store. Search Go. Item Add to Wish List. More Details. Rout the tenon. Note: Duplicate tenons may now be routed without having to mark or sight the tenons.

The Mortise. Clamp the mortise board to the jig with the mark aligned to the sight. Joint Fit. Fit the mortise and tenon together to check for joint fit. Adjustments can be made if necessary. The FMT Pro is designed for use by woodworkers of all levels.

Fein Turbo Ii Hepa Set Extra Fine Cut Hand Saw Dataset Filing Cabinet Locking Mechanism In