The term "power tool" in all of the warnings listed below refers to your mains-operated corded power tool or battery-operated cordless power tool. Cluttered or dark areas invite. Power tools.

Distractions can cause you to lose control. Never use the cord for carrying. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords. When using an extension cord, be sure to use one heavy. An undersized cord causes a drop in line voltage resulting in loss of power and overheating. Table kreg foreman semi-automatic pocket hole machine full on Kreg Foreman Pocket Hole Machine Manual Full the following page shows the correct cord gauge to use depending on cord length and nameplate ampere rating.

If in doubt, use the next heavier gage. The smaller the gage number, the Kreg Foreman Pocket Hole Machine Uk Id heavier the cord. Do not use a power tool while. A moment of inattention while operating power tools may result in serious personal injury. Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses.

Use a face or dust mask when the cutting. Make sure the switch is in the offposition before plugging in. Carrying power tools with your finger. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected.

Use clamps or a vise to hold work when practical. This is safer than using your hand and it frees both hands to operate the tool. Serious injury could occur if the tool. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Use of kreg foreman semi-automatic pocket hole machine full devices can reduce dust-related hazards. Use the correct power tool for your application.

The correct power tool will do the job better and. Any power tool that cannot be controlled with the switch is. Such preventive. Turn power off. Power tools are dangerous. Check for misalignment or binding of moving parts, Kreg Foreman Semi Automatic Pocket Hole Machine Youtube breakage of parts and any other condition that may affect power tool operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

Using improper accessories may cause personal injury. Use of the. This ensures that the. This plug fits in a polarized outlet only one way. If the plug does not fit fully. If it still does not fit, contact a qualified electrician to install the proper outlet.

Do not change the plug in any way. Never stand. If you have questions. The symbols and their definitions are as follows:. Dust created by sanding, sawing, grinding, drilling, and other construction activities may contain chemicals known to the. State of California to cause cancer and birth defects or other reproductive harm.

Examples of these chemicals are:. Your risk from exposure to these chemicals depends on how often you do this type of work. To reduce your exposure, work in a well-ventilated area with approved safety equipment, such as a dust mask specifically designed to filter out microscopic particles.

Extension cords are only to be used for temporary purposes. They do not replace the need for installation of outlets and proper wiring where necessary. Extension cords with an equipment grounding conductor must be used at all times. Extension cords must be protected from damage, and not run through doorways or windows where the doors or windows may close, causing damage to the cord.

Extension cords should be a minimum of 16 AWG and be rated for the equipment in use. Extension cords must be periodically inspected to ensure that the insulation and conductivity of the wires are not compromised. Extension cords should not be run through water or allowed to have connections that may be exposed to accumulated water.

Congratulations on kreg foreman semi-automatic pocket hole machine full a Kreg Foreman DB kreg foreman semi-automatic pocket hole machine full pocket-hole machine. Please read all instructions and safety information contained in this manual before using this product. Owning a Foreman gives you all the advantages of a true production pocket-hole machine with the compactness and portability of a bench-top tool.

This manual guides you through the steps necessary to adjust your machine and drill pocket holes. In addition to this manual, you may find the following resources helpful:. Kreg Online: To order more pocket-hole screws, view accessories available for your jig, or get help making a particular joint, go to kregtool. Kreg YouTube Channel: For project, product, and tip videos, visit youtube.

Kreg on Facebook: Connect with Kreg on Facebook to share your projects and get inspiration from our fans and friends at facebook. Always disconnect the machine from power before assembly, kreg foreman semi-automatic pocket hole machine full the access cover, or making any adjustments.

Push down on the control arm 1release the arm lock 2 at the back of the machine base 3and guide the control arm to the fullup position. Do not let the arm snap into the full-upright position. For transportation and storage, push down on the control arm and engage the arm lock.

Never lift or carry the machine by the control arm. Always use the handles 4 at the front and rear of the machine. In addition to helping keep your work area clean, efficient chip removal speeds drilling time and reduces heat build-up, extending the life of your drill bit. A Foreman with the chip-removal system installed must be connected to a shop vacuum when in use.

Not connecting the chip-collection system to a shop vacuum causes chips to collect in the hose and vacuum shroud and eventually clog the drill bit. The Foreman can be used without the chip-collection system in place. If you install the system and find that you must use your Foreman without a shop vacuum, simply disconnect the vacuum hose from the vacuum shroud. To install the chip-removal system, turn the Foreman onto one side kreg foreman semi-automatic pocket hole machine full from the inside of the machine base 3insert the vacuum port.

Fasten the vacuum shroud 7 to the machine with four truss-head machine screws 8. Slip the hose clamps 9 over the ends of the vacuum hose 10 and slip the vacuum hose ends onto the vacuum port and vacuum shroud. To make it easy to disconnect the vacuum hose from the vacuum shroud when working through the access panel 11orient the front hose clamp with the screw head facing the front of the machine.

Tighten the clamps and turn the Foreman upright. The access panel should be flush with the machine top right out of the box.

Should it need adjustment, use the following procedure:. Place the machine on saw horses so you have access to the bottom of the machine. Lay a straight edge across the machine top 12 and access panel Use the 3mm hex wrench 13 supplied with the machine to turn the cover levelers If the fence 16 can be moved with moderate pressure, tighten.

Rotate the handles counterclockwise unlocked position and verify that the fence moves freely. Should it ever be necessary to disassemble the fence locks, the fence-lock bases 18 must be oriented with the flat area indicated in the drawing facing the fence. The Foreman makes this easy, in just four simple steps:.

For a strong joint, the pocket screw should exit at the center of the workpiece thickness. This is accomplished by adjusting kreg foreman semi-automatic pocket hole machine full fence position. Unlock the fence 16 by rotating the fence-lock handles 15 counterclockwise.

Align the rear edge of the fence with the workpiece thickness marks 19 kreg foreman semi-automatic pocket hole machine full into the machine top 12 that correspond to your workpiece thickness. Rotate the handles clockwise to lock the fence in place. Kreg offers a complete line of pocket screws for every workpiece thickness and type. Use this guide to select the correct screw length.

Under Sink Drawer Unit Review Magnolia Wood For Turning Table