JET® 14" /4HP Bandsaw with Machined Aluminum Fence System | JET® Woodworking Tools

M Ph. Its purpose, aside from machine operation, is to promote safety using accepted operating and maintenance procedures. To obtain maximum life and efficiency from your band saw and to aid in using it safely, please read this manual thoroughly and follow the instructions carefully.

If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can provide quick service or information. For the name of an Authorized Service Center in your area, please callor visit our web site at www. For complete, up-to-date product information, check with your local WMH Tool Group distributor, or visit our web site at www.

This Warranty does not apply to defects due directly or indirectly jet 14 inch bandsaw manual error misuse, abuse, negligence or accidents, normal wear-and-tear, repair or alterations outside our facilities, or to a lack of maintenance. To take advantage of this warranty, the product or part must be returned for examination, postage prepaid, to an Authorized Service Center designated by our office.

Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection discloses a defect, we will either repair or replace the product at our discretion, or refund the purchase price if we cannot readily and quickly provide a repair or replacement.

This warranty gives you specific legal rights; you may also have other rights, which vary from state to state. WMH Tool Group sells through distributors only. Members of the WMH Tool Group reserve the right to effect at any time, without prior notice, alterations to parts, fittings and accessory equipment, which they may deem necessary for any reason whatsoever.

Warranty and Service Read and understand the entire owners manual before attempting assembly or operation. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury.

Replace the warning labels if they become obscured or removed. This band saw is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a band saw, do not use until proper training and knowledge have been obtained.

Do not use this band jet 14 inch bandsaw manual error for other than its intended use. If used for other purposes, WMH Tool Group disclaims any real or implied warranty and holds itself harmless from any injury that may result from that use. Everyday eyeglasses only have impact resistant lenses; they are not safety glasses.

Before operating this band saw, remove tie, rings, watches and other jewelry, and roll sleeves up past the elbows. Remove all loose clothing and confine long hair. Non-slip footwear jet 14 inch bandsaw manual error anti-skid floor strips are recommended.

Do not wear gloves. Wear ear protectors plugs or muffs during extended periods of operation. Some dust created by power sanding, sawing, grinding, drilling and other construction activities jet 14 inch bandsaw manual error chemicals known to cause cancer, birth defects or other reproductive harm.

Your risk of exposure varies, depending on how often you do this jet 14 inch bandsaw manual error of work. To reduce your exposure to these chemicals, work in a well-ventilated area and work with approved safety jet 14 inch bandsaw manual error, such as face or dust masks that are specifically designed to filter out microscopic particles.

Do not operate this machine while tired or under the influence of drugs, alcohol or any medication. Make certain the switch is in the OFF position before connecting the machine to the power supply.

Make certain the machine is properly grounded. Make all machine adjustments or maintenance with the machine unplugged from the power source. Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting wrenches are removed from the machine before turning it jet 14 inch bandsaw manual error. Keep safety guards in place at all times when the machine is in use.

If removed for maintenance purposes, use extreme caution and replace the guards immediately. Make sure the band saw is firmly secured to the floor or bench before use. Check damaged parts. Before further use of the machine, a guard or other part that is damaged should be carefully checked to determine that jet 14 inch bandsaw manual error will operate properly and perform its intended function.

Check for alignment of moving parts, binding of moving Jet 14 Inch Bandsaw Manual 2019 parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced. Provide for adequate space surrounding work area and non-glare, overhead lighting.

Keep the floor around the machine clean and free of scrap material, oil and grease. Keep visitors a safe distance from the work area. Keep children away. Make your workshop child jet 14 inch bandsaw manual error with padlocks, master switches or by removing starter keys. Give your work undivided attention. Maintain a balanced stance at all times so that you do not fall or lean against the blade or other moving parts.

Do not overreach or use excessive force to perform any machine operation. Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for which it was not designed. The right tool will do the job better and safer. Use recommended accessories; improper accessories may be hazardous. Maintain tools with care. Keep blade sharp and clean for the best and safest performance.

Follow instructions for lubricating and changing accessories. Make sure the work piece is held firmly against the rip fence or miter gauge as it is fed through the blade. Turn off the machine before cleaning.

Use a brush or compressed air to remove chips or debris — do not use your hands. Do not stand on jet 14 inch bandsaw manual error machine. Serious injury could occur if the machine tips over. Never leave the machine running unattended. Turn the power off and do not leave the machine until it comes to a complete stop.

Remove loose items and unnecessary work pieces from the area before starting the machine. This means that if precautions are not jet 14 inch bandsaw manual error, it may result in serious injury or possibly even death. This manual contains instructions on installation, jet 14 inch bandsaw manual error precautions, general operating procedures, maintenance instructions and parts breakdown.

This machine has been designed and constructed to provide years of trouble free operation if used in accordance with instructions set forth in this manual. WMH Tool Group can also be reached at our web site: www. Specifications Model Number The above specifications were current at the time this manual was published, but because of our policy of continuous improvement, WHM Tool Group reserves the right to change specifications at any time and without prior notice, without incurring obligations.

Report any damage immediately to your distributor and shipping agent. Read the instruction manual thoroughly for assembly, maintenance and safety instructions. Stand Assembly partial quantity shown 4 — rubber grommets 40 — M8x16 carriage bolts 4 — M8 lock washers 40 — M8 flat jet 14 inch bandsaw manual error 4 — M8 hex nuts 40 — M8 lock washers 40 — M8 hex nuts D.

Pulley Cover to Stand 3 — M5x12 pan head screws approx. Saw Body to Stand 6 — M5 flat washers 4 — M8x40 hex cap screws approx. Motor to Stand 1 — M8x80 hex cap screw for table stop - 4 — M8x35 hex cap screws approx.

Saw Body to Stand D. Strain Relief Plate to Stand 2 — M5x12 pan head machine screws. Tools Required for Assembly Metric combination wrench set and adjustable wrench 1 and 2 cross point screwdrivers. Place stand top upside down on a level Figure 1 surface.

Fasten four stand legs to stand top using carriage bolts, washers, lock washers, and nuts, as shown in item A on page 7. Note: Stand legs fasten to outside of stand top Figure 1.

Do not tighten at this time. Fasten two long braces and two short braces to stand legs using carriage bolts, washers, lock washers, and nuts, as shown in item A, page 7. See Figure 2. Turn assembly over and stand it on its legs. Push down slightly on the top to make sure the stand settles properly and all four legs sit flat on a level surface.

Tighten all nuts. Figure 2 Saw body is heavy! Use caution when lifting and stabilize until firmly attached to the stand! Failure to comply may cause serious injury!

With the aid of a second person, lift the saw body out of the shipping container and place onto the stand top. See photo on cover for orientation. Line up holes in saw body with holes in stand.

Place support plate to the underside of stand as shown in the parts diagram for the open stand assembly item 5, page Fasten saw body, stand, and support plate together with four hex cap screws, eight flat washers, four lock washers, and four hex nuts, as shown in item B on page 7.

Operating Instructions and Parts Manual inch Woodworking Band Saw Model: JWBSOS JET New Sanford Road LaVergne, Tennessee Part No. MA • JET products carry a limited warranty which varies in duration based upon the product. (See chart below)File Size: KB. Operating Instructions and Parts Manual inch Deluxe Pro Band Saw Models: JWBSDXPRO (Shown with optional Rip Fence) JET New Sanford Road LaVergne, Tennessee Part No. M Ph.: Revision D1 09/ Warranty and Service. JET Location: (Shown with optional Rip Fence). 21 rows · JVS, 14" Metal/Wood Vertical Variable Speed Bandsaw: Manual: JK, .

Hand Wood Carving Ideas Kr Make A Bowl Out Of Wood 4k