Due to natural variations in castings, blade thickness or den- sity and tire wear, absolute perfect centering alignment is rarely attainable. The blade length is 72 inches. For more information about our products, please visit our website at www. Loosen the lower thumb screw F. Table Of Contents. Pinch a Jet 14 Inch Bandsaw Manual Error ich gauge C between one of the guide 5.

Table of Contents. Previous Page. Next Page. This bandsaw has been carefully tested and inspected before ship- ment and if properly used and maintained, will provide you with years of reliable service. To remove a blade.

Make sure all stand fasteners are firmly tightened and that the stand cabinet is installed on a solid, flat and sta- ble floor that is able to support the weight of the bandsaw LBS 87 kg The bandsaw is heavy. Verify that the long table and the table alignment pin B from the table bolts C in the center of each trunnion are pointing slot. Page Blade Selection Blade teeth are sharp. Use care when handling a saw blade. Open the top and bottom wheel cover doors and bring the left hand side of the loose blade toward you and out of the left hand blade guard slot F.

Note: You may want to use a thick shop towel to handle the loose blade or wear a pair of heavy duty work gloves. Page Adjusting Blade Tension When working with narrower blades, sawing shorter stock and making tighter curved cuts are best per- formed using less tension This model M1 bandsaw is equipped with a blade tension scale, which can be used as a reference for the ideal setting with various blade widths. Ideally, the blade should stay relatively centered on both the upper and lower wheels.

Due to natural variations in castings, blade thickness or den- sity and tire wear, absolute perfect centering alignment is rarely attainable. Pinch a feeler gauge C between one of the guide 5. Loosen the lower thumb screw F. Turn the micro lower adjust nut G to move the guide screw E to set the gap between the guide block block assembly in or out until the guide blocks are and the blade.

Low speed is to be used for cutting soft woods over 4" in height or hard woods over 2" in height. High speed is best for cutting soft woods under 4" in height or hard woods under 2" in height. Note: If wood starts to burn at high speed, stop and change to the lower speed setting.

Report any damage immediately to your distributor and shipping agent. Read the instruction manual thoroughly for assembly, maintenance and safety instructions. Contents: Container 1 1 saw body 1 v-belt 1 trunnion support 1 main table 1 extension table 2 table lock knobs Page 12 With the aid of a second person, lift the saw body out of the shipping container and place on top of the stand.

Be sure front of saw with Powermatic logo faces curved stand front. Use caution when lifting Page 13 Loosen the nuts on the four motor mounting bolts Fig. Tighten the four motor mounting nuts. Page 14 To mount the main table, remove pin and insert from the table Fig. Rotate the table so that the saw blade will slide through the slot in the table. Then orient the table so the screws will slide into the holes on the trunnion support. Page 15 The air hose, which is already connected to the saw body, should be inserted through the hole in the stand and connected to the nozzle of the air regulator Fig.

Use a lighter or match to briefly heat the end of the hose so that it will slip over the nozzle. Install blade tension lever Fig. Mount the two miter gauge hooks A, Fig. Page 17 Mount front rail A, Fig. Do not tighten yet. Mount guide rail A, Fig. Page 18 Thread a hex nut A, Fig. Secure in place using a hex nut, lock washer and flat washer D, Fig. The hook C, Fig. Page Tilting The Table For resawing operations attach the resaw guide Fig. There is a slotted hole in the fence that will accomodate the resaw kit.

Position the resaw guide so that it is centered with the front edge of the saw blade. Tighten jam nut to hold table stop in place. Unlock the table and tilt it back on to the table stop to confirm table is 90 degrees to the blade.

Place tension lever in the highest position, as shown in Figure Turn blade tension knob B, Fig. A gauge on the upper wheel slide bracket C, Fig. Close upper wheel guard. Loosen lock knob A, Fig. Blade must already be tensioned and tracking properly. Loosen thumb screw A, Fig.

Saw unplugged 1. Check plug connections 2. Fuse blown or circuit breaker tripped 2. Replace fuse or reset circuit breaker 3. Cord damaged 3. Replace cord Does not make accurate 1. Description Size Bandsaw Blade To order parts or reach our service department, call between a. CST , Monday through Friday. Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately. Page 27 Hex Nut Cover Upper Back Pan Head Flanged Screw Tapping Screw Guard Blade Rear Page 28 Socket Set Screw

Oak Closet Rods Home Depot 40 Wood Carving Kit Harbor Freight 5g