It's easiest to start at the center and work around the the hole clockwise, sneaking up on the final size with a few light passes. Het ziet er namelijk erg eenvoudig uit. I put the base plate on and measured from the tip of the bit to the outer edge of the router base plate. While these hole patterns are specific, you could use my diy router circle jig gui with success for about any router. For the moment we are not using this one.

I put the base plate on and measured from the tip of the bit to the outer edge of the router base plate. Next it was time to attach the piano hinge onto the two pieces of plywood.

In order to get the best accuracy from this jig its important to attach the two pieces as close as possible. So I clamped them lightly to each other.

Then I put some double sided tape on the piano hinge and placed it so the barrel of the hinge was right on top of where the two parts met. I predrilled the holes using a vix bit, or center finding bit. This bit is great for hinges like these, it ensures that you are drilling perfectly centered into the hole. I placed the screws in the outer ends before pre-drilling all the holes in the center.

Once I put the screws in the outer ends, I moved the clamps towards the center then proceeded to pre-drill the rest of the holes and then put all the screws in place. To use the jig, all you have to do is line up the edge of the narrower piece with your cut mark and clamp it down.

Because I measured from the center of the v-groove bit to the outer edge of the baseplate, I can use this jig for multiple sized bits and the cut line will always be in the center. The important thing to remember with this jig is that it will always cut in the center, so you have to keep that in mind when marking out lines for cuts.

I hope that was helpful and now I need to go use it for my next project! Collapsible Bandsaw Bowls. Adjustable Dado Jig. Geometric Veneer Record Player Stand. Sunburst Veneer Guitar. Hand Tool Sharpening. Interlocking Puzzle Joint. Pool Toy Storage. Modern Storage Bench. Multi Function Cross Cut Sled. Epoxy glue is a two-component adhesive.

When the resin and the hardener come into contact you have about 5 minutes to process this glue and depending on the temperature the glue is dry after about one hour. Subscribe to my newsletter and be the first to be notified when I post new content on my website. To quickly and easily attach the mold to the router, we now will make a piece that ensures a firm and tight connection.

You can also use a piece of scrap wood for this connection part. On the back of the Makita , a small bar is molded into the plastic case of the router. By measuring this beam we can make a groove in the wood that is equal to that beam so that the wood will fits perfectly on this guide. The connection between the mold and the router must be tight. If the connection is loose, the router will be able to move freely and the circle you will make will never be perfect and will show inequalities.

I made the slot in the wood with my crosscut sled and the table saw. The height of the saw blade should be set equal to the height of the little bar on the back of the router.

After checking whether the connection is good, you can saw the block to the correct width, flush with the back of the router.

In order to clamp the block between the router base and the button, a slot must be made so that the piece can slide over the bolt. We will make that slot by clamping the piece on my crosscut sled, Diy Router Circle Jig Map setting the saw blade to the correct depth and sawing the slot to the width equal to the thickness of the clamping bolt.

To attach this piece to the threaded rod we will drill an 8mm hole. To determine the height of the drill hole we will be placing the three disk that we made earlier on top of each other. The circle with the slot should now be at the top and the opening of the slot determines where to drill the hole in this piece.

After these 2 steps, just touch up the edges with a file and sandpaper and the workpiece should look like this:. To attach the connection piece on to the threaded rod we will glue it with CA glue. Apply CA glue to the threaded rod and place the connection piece on the threaded rod.

The slot should be on the outside and the end of the threaded rod should not go beyond the inside of the slot. After the connection piece is in the right position, the accelerator that instantly hardens the glue can be sprayed on. Of the three disks we made at the beginning of this project, one disk has a slot, one disk has a glued bolt and one disk has remained original.

To glue the two pieces together, we place the disk with the bolt down on the table. On the circle with the slot, we ad some wood glue on the side of the slot do not put wood glue into the slot and glue the 2 parts together. Wood glue does not become firm until it can dry under pressure. Therefore you can clamp these 2 parts or use brad nails as I did. If you do not have a nail gun, you can alternatively use small nails.

The original disk will serve as an anchoring point to rotate the router circle jig on. For the moment we are not using this one. Now that all the pieces are ready, they can be brought together. On the threaded rod, we first place a nut followed by a washer. Then we slide the threaded rod through the opening of the center rotation point. To fix the threaded rod on the center point, we place a washer on the outside again, followed by a nut. This Router circle jig is very easy to operate.

Start by connecting the jig to the router. Slide the connection piece behind the clamping bolt and tighten it. Take your workpiece and determine the middle on your workpiece. Mark this center point with a pencil so that it is clearly visible. Apply double-sided tape to the bottom of the third disc. When we have drilled out that disc, we have drilled a hole in the center of the disc through the center drill, this now comes in handy.

Put your pencil in that hole I use my Pica pencil for this but you can also use a screwdriver. Place the point of the pencil on the previously marked center and now lower the disk. This way you have placed the disk perfectly in the middle of your workpiece. Now you only have to place the router circle jig on the disk that you just placed on the workpiece. Do this by entering the bolt into the hole of the disk you just placed on your workpiece. Make sure you tighten the nuts properly!

Due to the vibrations of the router, these can come off and the diameter of the circle will change. Building a workshop can be tough and involves a lot of trial and error. I know because I was there too.

Thanks to this training, I gained better insights into building a workshop so that I could spend my budget more efficiently. Do you have an addition to this blog or an upbuilding comment?

Feel free to let me know in a comment below. Contribute to our community and share your experience and knowledge with others so that we can all learn from each other.

I hope this information was helpful and that this blog and video inspires you. Let me know in a comment below. Feel free to share this blog on Facebook, Pinterest or other social media. You can do this by using the buttons below or at the top of the blog.

I would appreciate that. Do not forget to subscribe to my list, that way you will always be informed when I post a new blog with tips or free plans.

Dag Christofix, ik heb een vraag. Volgens mij gebruik je lijm met een versneller of accelerator. Welke lijm is dat en waar kan ik het kopen? Het ziet er namelijk erg eenvoudig uit. Alvast dank voor je antwoord, groeten, Evert. Hoi Evert, Dat is lijm van starbond. Bovenaan deze blog kan je een link vinden in de materialen lijst.

Ik heb deze lijm toegestuurd gekregen door starbond om te testen en ik ben er super enthousiast over. De lijm is snel en sterk. Absoluut de moeite! Hopelijk heb ik je kunnen helpen. Indien je nog vragen hebt mag je me steeds een emailtje sturen. Christo, I just found your website. The build instructions are much more complete than any of the other sites.

I do have one small problem: here in America; we use imperial units.

Jet Planes Art Zone Make A Frame Clamp Javascript Belt And Disc Sander Philippines Questions