Easy Woodworking Projects For The Kitchen

All opinions are my own. This post also contains affiliate links. See disclosure policy for details. Building your own DIY kitchen cabinets seems like a pretty intimidating project…or is it just me? No big deal! Do your best and caulk the diy kitchen woodworking projects 85, right?? But, you know what I found out?? A Note About Cabinet Depth: I built these DIY cabinets frameless, with full overlay doors to avoid having to use anything except plywood to build them.

If you want to change the depth of your own cabinets, rip your plywood narrower or wider as diy kitchen woodworking projects 85. I saved the thin strip leftover to use later as the top supports. Diy kitchen woodworking projects 85 a detailed guide on how to cut down a plywood sheet, check out this post.

Save this for your shelves later. For this, I used my Kreg AccuCut and circular saw for quick, clean cuts. See more on how to cut down plywood here. From the remaining plywood, I cut the bottom panel. Check out this post for door sizing guidance. That is the length you need to trim your bottom panel and top support pieces.

Remember that thin strip leftover from step 1 ripping the plywood for base cabinets? Most kitchen cabinets have toe kicks on the base cabinets.

You can go without toe kicks, but I am pretty careless and rough on things, so Diy kitchen woodworking projects 85 would be accidentally kicking the bottom of the cabinets constantly and scuffing them up. So I added toe kicks. The corner where these lines meet needs to be cut out with a jig saw. The last detail before assembling the carcasses, is adding edge banding. I drilled pocket holes along the side edges of the bottom panel and the ends of the support pieces.

Then, I attached the three support strips so that one runs along the back, and two along the top-one in the front and one in the back. Make sure the one in the front is the one with the edge banding applied. That gives you your cabinet box. Adding the backs sounds pretty simple…and it is. Make sure when cutting your back panels, that they are square and make sure when you attach them, that your cabinet is also square to this back piece.

Simply nail or staple in diy kitchen woodworking projects 85. Now, I made full overlay doors for most of my cabinets. I wanted the entire cabinet carcass to be hidden and basically let the doors steal the show. Make sense? Once they were cut to size, I applied hickory edge banding to all sides of the doors and sanded well. Check that out for all the details. Lastly, I added some shelves using shelf pins so they are adjustable.

Now, to install these cabinets, I used shims to level them up where they go, screwed them TOGETHER through the side panels, then attached them to the studs in the wall through the top back support. Once all the base cabinets were in place, I glued up a solid hickory wood countertop like in this post and attached through the top supports of the cabinet boxes.

You can install whatever type of countertop you prefer. And the final piece, was adding the toe kicks at the bottom. Then just nail diy kitchen woodworking projects 85 the carcass side panels using finish nails. Now, the plywood strips have been cut for the upper cabinets in step 1.

But they need to be cut to length and assembled. Upper cabinets diy kitchen woodworking projects 85 a little trickier as your side panels will vary depending on if you want them to go to the ceiling, how high your ceilings are and how far off your countertop you want them to be. I wanted my cabinets to go all the way to the ceiling, BUT I was adding a piece of trim between the cabinet and the ceiling and needed something to nail that trim to.

That way, when I diy kitchen woodworking projects 85 my cabinets, I can attach the trim along the top of the cabinets and have something to nail to. This time, I attached thin plywood strips between the side panels—one at the top and one at the bottom—like shown below. This is so how you will hang them diy kitchen woodworking projects 85 the wall. Then install them by diy kitchen woodworking projects 85, shimming, and attaching them together and into the wall studs through the support pieces on the back.

As a side note: you can easily modify the dimensions and use these instructions to build a pantry and a refrigerator box cabinet as well. Depending on your own preferences and how you built your cabinets, adding this trim is optional. You could do crown molding or some other type of trim, but I just kept it simple and modern. You can finish the cabinets before or after installation…I painted the uppers before installing and polyed the base cabinets after.

I simply applied a few coats of Minwax Helmsman Water Based Poly on the bottom cabinets and the countertop. And for the top cabinets I applied one coat of Kilz primer water basedand two coats of Sherwin Williams Dorian Grey on top after it dried. Once the finish is dry, you can add your door and drawer hardware. I also used these same pulls on my DIY modern nightstands recently. See, now? And if you want more details on the backsplash tile, check out this tutorial.

But…I have no doubt that if I can do it, you can, too. What did you use for your counter tops? And what color did you paint the upper cabinets- I love it! Hi Amy! Thank you so much! I love that medium grey color, but also recommend Dovetail by Sherwin Williams as well.

Good luck with your laundry redo! Thank you! The countertops are made from solid hickory that I purchased from the local hardwood place.

I glued them together to make a butcherblock style countertop. Facebook Instagram Pinterest YouTube. DIY Kitchen Cabinets.

Aug 24,  · Diy reclaimed wood projects can come in all shapes and sizes from ideas for the bathroom to the garden, to the kitchen sink! You can get amazing results from using reclaimed wood and perk up a space that might need a little help, like a bedroom headboard. Mar 18,  · Find complete how-to instructions on this woodworking crafts project here. Be sure to use water-resistant wood glue, and keep your board out of the dishwasher or it might fall apart. And one more thing: Keep the boards as even as possible during glue-up to minimize sanding later. For great tips on gluing wood, check out this collection.

Accuride Drawer Slide Replacement Parts Australia Kingsbury Jig Tool Group Ltd Carbide Tipped Woodturning Tools Uk Model