Craftsman Table Saw Dust Collection System Generator,Best Woodworking Bench Plane Design,2 Bhk Flat Wood Work Hyderabad Sale,Furniture Pulls With Backplates Day - Step 2
10.08.2020When I decided to get into woodworking, I had the unbelievable opportunity to add this beautiful old Craftsman contractor saw to my arsenal. This thing is an absolute gem that dates back to the s or even the 50s.
Then I slid it into place as far as I could and marked where the motor supports will intersect with it. My plan was to cut a slot for the supports from the right side, so that I can slide the piece into place from the left.
I was also going to have to contend with the belt, which I figured would call for another slot. I used a piece of paper to make a super rough template for the opening. Then I cranked up the blade as hight as it goes to craftsman table saw dust collection system generator for the maximum belt movement. With my craftsman table saw dust collection system generator roughed out, I transferred it to the MDF backer and pulled out my trusty jigsaw to cut it out.
Since the supports are big rods, the end of the support slot can be curved for a snug fit. So I marked the center point and used a Forstner bit to drill the hole that will become the end of the slot. With the hole tzble, I set up a straight edge for my jigsaw to register against and cut craftsman table saw dust collection system generator slot from the hole outward. This took a little fidgeting because I first cut it a little too snug and had to come back craftsman table saw dust collection system generator open it up a bit further.
The first obstacle I ran into was when I noticed that the motor support bracket slides in as the motor raises. Which means it dug into the backer piece and left cllection handy mark for me to see. I used my jigsaw to cut a slot for it to have a little wiggle room. I also noticed that the belt was uncomfortably close to the top of the opening when raised the blade all the way generayor. I used my chisel to angle the slot and make some more room for the saa. The next obstacle I ran into was that the hook on the back side of the rip fence bumped into the top of the backer.
I marked where to put a rabbit cut and used my dado stack to hog out some room. With the backer out of the way, I turned my attention to the bottom. The bottom of the saw is wide open and allows the dust to fall right through. My father-in-law had helped me build the rolling table the saw sits on and we cut an opening with the plan of building a box on the underside to catch the dust and let my dust collector whisk it away.
Time got the better Ridgid Table Saw Dust Collection System 20 of us that day, so I my plan was to run with the box idea. I took some measurements and came up with a rough model in my mind. Then I craftsman table saw dust collection system generator to work cutting the MDF to build it. I then traced around my dust collection hose and used my jigsaw to cut the opening. I pretty much suck at cutting holes with the jigsaw, apparently, but it turned out well enough to provide a reasonably snug fit for the hose.
Next, I drilled some pocket holes into the sides to attach the box to the underside of the table. I then predrilled and screwed the box together. I could have used a sytsem hand here, but my kids were in bed at this point and I had to make do. And, of course, the box cust too big. After debating the level of effort of removing the saw from the table so I could just flip the table over, I finally decided it was less work to just dismantle part of the box, slide it through, then put it back together.
Then I had my daughter help me hold it craftsman table saw dust collection system generator place while I struggled to screw in the pocket hole screws. I still get sawdust that comes across the top and through some of the other openings, but this drastically cuts down on the messes Collectioh make with this saw.
If you like this post, consider signing up for our mailing list. Thanks for stopping by. Save my name, email, and website in this browser for the next time I comment.
Shop Builds. No comments yet dust collection table Contractor Table Saw Dust Collection Inc saw. Leave a Reply Cancel reply. Building a Wine Bottle Gift Box.
Small Wooden Items Zombie Diy Mobile Woodworking Bench Jp Wood Craft Dowels Llc |
10.08.2020 at 16:35:57 Control and capability to deliver perfect results development systems.
10.08.2020 at 23:19:18 May contain affiliate help those of you that are ready to dip your toe for those.
10.08.2020 at 11:11:12 Often comes down to personal dewalt out.