Then draw the free end against the form with benring one-handed bar clamp. Subscribe on Youtube. Your scheme for straightening the neck via steam and then locking it into a straight shape might work. Begin to bend the blank around the form. Also, it might be tricky to get it to cool to retain a true and straight shape.

Cut the plywood to the dimensions that you need. The interior of the steam box should be large enough so that when you load it up with wood there will still be an inch of space around the wood so that the steam can get to the wood. Nail or screw the 4 sides together. Close off one end of the box. Leave the other end open. Screw a piece of plywood that is 4 inches wider than the diameter of your cooking pot to the capped off end of the steam box.

Cut a hole in the center of the piece of plywood so steam can get from the cooking pot into the steam box. Drill some holes in the side of the box to run your wire supports through. Keep the holes the same diameter as the wire to minimize the amount of steam that escapes or the need to do a lot of caulking. The wires will elevate the wood in the box so the steam can get to all sides of it.

Cut wires 4 inches longer than the diameter of the box. Run the wire through the holes and bend over the ends so the wires don't fall out. Finding the hole at the far side by feel is tricky. Shine a light in the open end of the box and look through the hole that you are aiming the wire for. When the light disappears, you have found the hole.

Set your pot up on the heater that you will be using. Screw some legs to the sides of Build A Steam Box For Bending Wood Version the open end of the box so that it is level with the top of the pot. The level steam box is important so that the lid of the steam box makes a good seal with the top of the cooking pot.

If you're not that ambitious, you can just pile stuff under the open end of the steambox to raise it to the right elevation. When you're all set, fill your pot two thirds full of water, turn on the heater and wait for the water to boil. After the water has come to a boil, the steam box still takes a little while to heat up. Once you get a good flow of steam coming out of the end of the box, you're ready to heat and bend. One quarter inch thick ribs heat up in under 5 minutes.

Thicker stock takes longer. Heat has to travel from the surface of the wood to the interior. Keep in mind that some woods bend better than others. White oak, red oak, ash and poplar all bend well. Straight grain is important as well. If you have rain running out of the face of the board, your wood will most likely break where the grain runs out. It's really easy to leave on the heat when you're done bending wood. Eventually, the water all evaporates, the pot becomes hot and the plywood starts smoking.

Good way to start a fire. The placement of the wire could be made easier by drilling of the holes and placing the wire As you assemble the steambox rather than after screwing the box together. Question 2 years ago. I have parts and pieces at my disposal that would allow me to make a steam tube that would SAFELY hold psi of pressure in the tube. That's my theory anyway. I was wondering if you know of anyone who has tried this approach?

Am I wasting time? The wood I want to bend is approximately 1" thick. Any suggestions or thoughts would be greatly appreciated. Answer 2 years ago. Waste of time. The most important factor is moisture content of the wood - the higher the moisture content the lower temp is required to loosen the bond between the lingin and fibers allowing the wood to be bent.

Putting a higher flow of steam or more constant, uniform coverage into the box might be a cheaper way of speeding it up. But speeding it up too much might not turn out well - just like turning the oven up to cook food quicker. Question 3 years ago on Introduction. Could a steam box be used to straighten a warped guitar neck? I would think that a box could be constructed that would contain only the neck portion that needs to be straightened, and which allows the guitar body and the head where the tuning pegs are to extend out opposite ends of the box.

Would there be an easier way? Also, it might be tricky to get it to cool to retain a true and straight shape. A straight jig would be important I'm sure. Anything else?

Or is the whole idea just a waste of time, trying to fix something that is already toast? Thanks, pquin3. Reply 3 years ago. I saw a technique for bending the sides of the body of a musical instrument using a wet rag around a large soldering iron. The wood is worked back and forth across the saturated cloth covered iron while applying pressure to bend it around the iron. I haven't actually tried this but it seemed like a good way to only apply the steam to the area of the bend.

Reply 10 years ago on Introduction. The question I would ask would be, what caused the neck to warp in the first place? If it started out straight, then warped, then is steamed back into position, what will stop it from warping again?

Your scheme for straightening the Build A Steam Box For Bending Wood Young neck via steam and then locking it into a straight shape might work. And if it does, you would be the world expert and could write an instructable about it. On the other hand, dried wood does not steam bend as well as wet wood or green wood, I assume guitar necks are made from well seasoned wood. Use small squares of wood in the box to Build A Steam Box For Bending Wood Youtube use as shoes.

These will prevent the planks from laying on the bottom of the box to ensure even steaming. You can adjust the size of your box if you need to. A box that is too small can build steam too quickly and damage the box.

In some cases the box can explode. As a general rule, you should keep wood in the box for one hour per inch of thickness. Always use gloves when you are working with steam. The steam can get hot very fast and cause burns unexpectedly. A lot of people will place the steam box on a wooden workhorse for ease of use. If you prefer, you can build legs for the steam box easily.

This is entirely up to you, and will depend greatly on how often you plan on using the box. We welcome your comments and suggestions. All information is provided "AS IS. All rights reserved. You may freely link to this site, and use it for non-commercial use subject to our terms of use.

View our Privacy Policy here. Toggle navigation subscribe. Building a Steam Box. Written by Doityourself Staff. What You'll Need. Enough wood for a 7 x 1 x 1 box. Steam Supply. Flexible PVC Hose. T Junction. Shadow Box Fence Painting Tips. Guide to Wallpaper Removal. How to Anchor an Iron Railing into Concrete. Solid Bridging. I asked my contractor this question he has the cable running w the steam pi Read More.

Smoke from residential chimney at 85 degrees I live in a tall building in New York City over apartments and there' I have several radiators with danfoss RA valves on them that are not he Schluter profile in shower.

Saber 375w Belt And Disc Sander Review Make Cabinet Drawer Runners Volume Drum Sander Machine Woodworking Projects To Sell On Etsy Android