Christmas Ornaments: Build Your Inventory Fast | Turning For Profit

If you would like to be notified when I post a new article, send me an email. I'll only use the list for that purpose, and I'll mail blind cc so turnung address won't be any the worse for spam.

If you have comments, questions, or suggestions I'd enjoy hearing from you. Just send me an email. My address is David DavidReedSmith. If it's a suggestion I'd be happy to post it along with this article. Let me know if you would like your email address posted as part of the attribution, or limited to only name, best wood for turning christmas ornaments chord only first name, etc.

This article in. I like to make different Christmas Ornaments every year to give to my relatives. The ornaments use a split turning of either a Christmas Tree or Snowman on a background frame. The frame can be made using a ring with contrasting veneer or turned directly from solid stock.

If you like the look of contrasting multiple woods for the ornament you should try making the frame out of a ring with a veneer backing. First mount a flat disk to use as a drive plate. You can mount a scrap piece of wood to a small face plate and turn it true and flat. To turn the rings start with a disk of solid wood about 3 inches in diameter. Mark the center of the disk, and hold it against the drive plate with your tail stock center as shown in Figure 2.

True the disk with a beet gouge. Use a parting tool to cut rings by cutting from the face and the edge. A disk held against a flat drive disk for cutting loose the rings. Cut some slightly oversize disks of veneer I traced the ring and used scissors.

Glue the rings to the veneer. Clamp the rings to the veneer I used plywood cauls and C-Clamps. Once the glue dries mount the frame, back side out, in a Chuck I used narrow wooden jaws on my Stronghold.

Trim the veneer and smooth the back part of the rim of the ring. Sand and apply a finish if you like to finish on the lathe. Reverse the frame in the chuck and true best wood for turning christmas ornaments chord the rest of the outside of the ring, the rim, and the inside of the ring. Add a decorative cove or bead to the rim if you like. Sand and apply a finish. Hot-melt will stick to finish about as well as it will to bare wood, which is best wood for turning christmas ornaments chord very well, of course, but Christmas Ornaments are not subject to best wood for turning christmas ornaments chord lot of stress.

Assuming you keep the cat out of the tree. Mount it in a chuck and true the back part of the disk and the back, sand and apply finish. Reverse the disk, true the rest of the edge, hollow the inside, then sand and finish. Rip two strips twice as wide as the wood is thick, then glue them into a turning square with a paper joint. I find this easiest to do by spreading glue in a thin coat over both pieces with a flexible piece of plastic, but you can also apply a bead of best wood for turning christmas ornaments chord on one and them rub them together.

Clamp well and let it dry overnight. Use ornamentw cup center in your tailstock a point will split the turning. If you want to use a collet chuck, turn a tenon between centers, then chrismtas it in your chuck. Follow approximately the dimensions given in Figure 3.

To make the body of the snowman, prepare a paper jointed turning square of light wood, such as bass wood, maple, or pine and mount it as you did for the tree. Follow the dimensions in Figure 3. Use a darker wood for the hat. Left-overs from the tree would be ideal.

Undercut the bottom of the hat so you can assemble it at a suitably rakish angle. The dimensions I ended up with. You don't have to slavishly measure, this cord gives you an idea to shoot for. Making the Hanger You could turn a small finial or even just glue a loop of mono-filament or ribbon to the frame to hang the ornament, but I used brass wire this year.

I made a simple bending form by drilling nail size holes in a scrap of maple, then whacking in nails and cutting them off. To make the hanger first cut off a best wood for turning christmas ornaments chord of brass wire, and wind it around the nails.

Tighten the hanger by twisting the base with a pair of pliers, then tamp it flat with a small scrap of wood, and remove from the bending form. To mount it in the frame drill a hole the size the twisted wire turns out to be. Put a drop of super-glue on a piece of waxed paper or aluminum foil, bezt dip the hanger in the glue and screw it into the hole in the frame.

The wire bending form. I start at the bottom, going best wood for turning christmas ornaments chord each nail in counter-clockwise order, then twisting to tighten up. Wpod and Adding Accents. To finish the ornaments, first split the turnings using a chisel or knife. Use hot-melt foor to attach the turnings to xhord frame. The last step is to add accents with puff paint. The finished ornaments.

Nov 18,  · Christmas ornaments don’t have to be made of glass or metal. I make wood ornaments, consisting of a hollow ball with a turned ring around its midsection and finials top and bottom. They’re turned ornaments, made on a lathe. Making these ornaments is a good way to use small scraps of exotic woods. Here’s how I go about it: Turning the ball. Pin by Jerry Haakonson on Ornament from woodturning christmas ornaments. Christmas period is arriving fast. A family nights Xmas carol karaoke is an enormous means to enter the holiday spirit. one day of indulgence won’t result in significant weight gain, so long as you intend to reunite on program with healthful food choices and exercise the following day/5(3K). Ornaments from Craft Supplies USA. Turned Christmas ornaments are fun to make for woodturners of all skill levels. From press together, pen mandrel-based Christmas ornaments to more advanced Sea Urchin and Birdhouse ornament kits, we have everything for making the holidays fun and bright.

Kreg Jig 5 Lowes 100 Flush Bitters 2020