Belt And Disc Sander Toolstation Game,Sauder Woodworking News Now,Kreg K4ms Master Pocket Hole Jig Kit For - 2021 Feature
02.05.2021I would most definitely recommend this sander to anybody that need to sharpen knives, work on home projects or do any crafts or hobbies involving removal of access material from things. Good value and quality here. Bearing issues after a while.
Thankfully, the Rikon sander proved to be a pleasant surprise: it's sturdy, well-made, easy to use, powerful, and it's more than you would expect for that price. It chews through hard woods and aluminum with ease; very little vibration, and the dust collection system is pretty good, too.
My only minor gripe is that it takes some work to change belts: instead of some sort of a latch or a thumb screw, you have to undo three screws with a screwdriver. And if you don't tighten them back, the cover will be prone to coming off when you connect your vacuum cleaner to the port. As other reviewers have noted, there are two separate dust collection outlets.
This complicates things a bit if you're putting together some sort of a permanent dust collection setup. But since I'm just connecting my vac when I need it, it's not a big deal for me. Edit: the sander has gotten increasingly loud after several months of intermittent use, to the point where you had to wear hearing protection just to turn it on. After some investigation, the culprit appear to be two low-quality bearings used for the smaller belt rollers.
The bearings are very cheap to replace, although the middle roller is relatively difficult to disassemble. Overall I recommend this without hesitation. Just received it and am totally impressed. Had bought a Harbor Frieght belt sander a couple years ago. By the time I tried the Harbor one, the motor bogged down with the least bit pressure and could not keep the belt on track.
When I plugged in and turned on this Rikon, I knew that this is one well built sander. The frame is all metal, tracks perfectly, has power to spare and the belt back piece that supports the belt is super strong. Wonderful sander. And it comes with a 5 year warranty.
The unit came defective. The belt could not be adjusted to track correctly and was eating into the housing immediately. It caused the shaft to be skewed and the roll pin to keep the tensioner from working correctly. I could not drive the roll pin in further, so I used needle nose vise grips to pull it out. Now I could see that the hole that was drilled for the roll pin was not straight from one side of the collar to the other collar.
Therefore, the pin could not seat itself in the far hole. The smaller of the two holes holes that actually holds the pin in. If I had attempted to use this unit as it was, the tensioner pulley would have eventually blown out and could have been dangerous.
I decided to attempt to fix it myself instead of sending it back. I removed the roll pin, used a drill bit to lightly straighten out the first hole, and then fitted the roll pin to be sure it would drive in straight when the shaft was inserted back in. I also spread the roll pin out a bit to make it hold better.
The pin was driven completely in afterward. I then noticed a second problem; the tensioner assembly was hanging on the housing, causing it to stick and not fully engage. I worked the tensioner by hand back and forth to wear the tensioner assembly in so it would move freely.
That worked after about 15 minutes of constant work. So far the unit now works well. It tracks the belt fine and holds the proper tension. The comical thing to all of this is the documentation that says that the belt should not need adjusting because it was adjusted at the factory.
That is a joke, as the belt could never have been adjusted. In a nutshell, the build quality is not good. The person drilling holes in the unit and the assembler should have caught this problem.
It was easy to see that the roll pin was sticking up and if the belt had been adjusted, then the person adjusting the unit should have immediately spotted the problem. In regards to the design of the unit, the belt guard is horrible. You need to remove the top clear guard and then three screws to remove the side guard. If you are sharpening knives, you will need to change the belt three times.
This guard mounting design is not acceptable. Rated 5 out of 5 by Arthur from Great performance Grizzly Combination Belt And Disc Sander Game I wish I'd bought this years ago Rated 5 out of 5 by Readerholic from Solid and powerful Larger and much more substantial than I was expecting.
Extremely easy to set up. The only improvement I can think of is it would have been nice to have a spare belt and disc included. But then the price would have been more, no doubt. A bargain, if this is what you need. Rated 5 out of 5 by Timp from A brilliant accessory to my workshop Brilliant piece of woodworking equipment Date published: Rated 5 out of 5 by CaptAwsum from Proper piece of kit Just purchased, after a long time researching.
Good purchase, will do me just fine Date published: Rated 4 out of 5 by Ed the woodwizard from Good piece of kit Good addition to the workshop only negative is the amount of dust it lets out while using it. The dust extraction is pretty rubbish and if using in a confined Belt And Disc Sander Toolstation Zip space i would advise removing the bag and fitting something more substantial. Related products. All delivery charges are charged to the customer upfront on finalization of sale.
Regrettably, we are not able to deliver to these areas: Alexandra, Dawn Park, Katlehong, Klipoortjie, Kraaofintein, Mamelodi, Mapleton, Ramphosa, Reigerpark, Rondebult, Roodekop, Tokoza, Villa Lisa, Vosloorus, Windmill Park If you have any questions about purchasing online, or require more information on split delivery, please contact our online customer care centre at [email protected] or call us on Item no.
Model HBS Added to your basket. Add to wishlist. Check stock in your local store:. Use my current location. Write a review Show All Show Less.
Long Dowel Sticks Update Rockler Router Lift Zero Wickes Garden Bench Plans Cabinet Drawer Bottom Slide With |
02.05.2021 at 16:59:11 Router Bits | Piece Set jointer.
02.05.2021 at 22:39:52 ЗАНАВЕСЫ СВЕТОДИОДНЫЕ ФИГУРЫ ГИРЛЯНДЫ - СЕТИ СВЕТОДИОДНЫЕ СОСУЛЬКИ Step-by-step written directions, and.
02.05.2021 at 21:45:12 Order to gather enough speed sell.
02.05.2021 at 20:56:51 Dedicated to making your carving experience the furniture piece, it is also functional because you.