Sign Up. Customer Care Woood to a friendly customer care representative to help with your purchase. Rustic hardwood isn't the cheapest of the bunch. Prep the floor 1 Begin by vacuuming the concrete floor to remove as much dust as possible. Woodworking Adventures.

Blind-nail every 16", placing nails between the face nail locations. Select board lengths so that butt joints in adjacent courses are offset by at least 2'.

Snug the next course against the nailed course by tapping the tongue to groove edges together using a 6"-8"-long block of scrap flooring as shown in Photo C. Repeat the nailing technique to drive nails every 16". Blind-nail successive floor board courses. As you get close to the opposite wall, use wood wedges to force tongue-and-groove joints together.

Use a nail set to set these nails below the wood surface. Then use a pry bar to force the final tongue-and-groove joint tight and secure the last boards in the last course by driving 6d finish nails every 16" as shown in Photo F. Note: Before turning on the sanders, be sure to slip on a dust mask and protective eyewear.

Have a shop vacuum ready to collect sawdust. If sanding in the basement, tape the basement door shut with duct or packing tape to limit the amount of sawdust penetrating the living spaces upstairs. Fit the groove of the mating floor board to the tongue of the nailed floor board; tap into place with a piece of scrap flooring and hammer.

When you no longer have the space to Wood Workshop Videos Zip Code use the flooring nailer, wedge the flooring board tight to its mating floor board and fasten it down. Face-nail the final course of floor boards, using a pry bar to pull them Wood Workshop Equipment Cad Blocks Zip Code tight to the neighboring floor boards. Cut in along the walls furthest from the door with the nylon pad, and follow with the larger applicator..

The drum sander works more aggressively and should only be needed if the edges of flooring boards stand proud of adjacent boards after installation. Start sanding in the back corner of the room farthest away from the door and move the sander parallel to the flooring courses as shown in Photo G. Keep the sander Wood Workshop South London Zip Code moving and let the weight of the machine take care of downward pressure.

Clean sawdust off shelves, cabinets, and light fixtures, and then wipe down the walls to remove any dust that might contaminate the floor finish.

Vacuum the floor thoroughly with a shop vacuum and wipe it off with rags. We used a water-based polyurethane from General Finishes High Performance Polyurethane in a satin sheen. This additive Enduro Crosslinker from General Finishes makes the finish harder, more durable, and adhere better. Use a clean mixing stick to blend the additive into the finish. For more control, we transferred the finish from the can into a clean spouted watering can. Pour a small amount of finish on the floor and then use a squeegee-like applicator to spread finish evenly ours is made by Padco; www.

Keep pouring and spreading until the floor is coated completely. Apply four coats in total, letting each coat dry between applications. To install baseboard, drive 8d finish nails through the baseboard and into studs at 16" centers. You must be logged in to write a comment. Log In. Find a Store. My Account. My Cart. Go to Home Page. Mobile Navigation. Same Day Shipping Find a Store. Search Go. Topics Cabinetry. Choosing Hardware. Dust Collection. Friends of Woodcraft.

Getting Started with Woodworking. You want it basic and you want it cheap. But you keep coming up empty. What are your options? Rated from worst to best, here are six options, with the top option being the clear winner. Highly damage-prone, laminate isn't wood; it only looks like wood. Slippery and easily damaged. Eliminate any type of engineered wood from your thoughts. Engineered wood's thin, top wood veneer isn't good protection against falling hammers.

Expensive and a poor choice, this is a clear "no. At one time, if you wanted solid hardwood, you got it unfinished and it was your responsibility to site-finish it. Better techniques evolved for pre-finishing wood flooring. Urethane-based coatings meant that manufacturers could impregnate the wood with a nearly shell-like finish, enabling the finishing process to happen in a factory, not your home.

Dropped hammers on pre-finished floors is not pretty. Dan McMillan of Carlisle Floors has said that one problem with pre-finished flooring is that this urethane finish must be chemically stripped before you can refinish it. Orient strand board, that amalgam of resin-bound wood chips, is an ugly and cheap dense option for your shop floor. But it chips off easily and swells with prolonged contact with moisture. Not only that, the rough surface is hard to sweep. OSB is good only as a sub-surface for other flooring.

Not recommended.

Wood Plank Desk Top Diy Jet 1020 Benchtop Drum Sander Reviews Incra 5000 Review List Woodworking Plans Magazine Holder 4g