Buff if necessary. Its important to wood veneer finish 30 particular attention to the finishing process. With each successive coat of finish, you should sand with finer and finer grits. You may freely link to this site, and use it for non-commercial use subject to our terms of use. Second: Water based polyurethane varnish.

Custom Products. Learning Center. Full Learning Center. About Our Products. Resources Links. DIY Project Ideas. About Us. Search for:. Talk With Us! All Veneers. Refacing Kits. Veneer Sheets. Not finding a specific species, size, or backer option? Give us a call at for help or special orders. Showing 1—30 of 80 products. Alder Wood Veneer — Flat Cut. Knotty Alder Veneer. Ash Wood Veneer, Flat Cut. Ash Wood Veneer, Quarter Cut. Carbonized Bamboo Veneer — Planked. Carbonized Bamboo Wood Veneer — Vertical.

Natural Bamboo Wood Veneer — Planked. Natural Bamboo Wood Veneer — Vertical. Steamed Beech Veneer — Flat Cut. Bubinga Wood Veneer, Flat Cut. Cherry Wood Veneer, Flat Cut. On the other hand, it is surprising how much sanding a veneered surface can take. The most common mistake that people make when sanding wood veneers is to go too easy or to use too fine of a grit.

Sandpaper comes in different grits. The coarsness of the grit Wood Whisperer Salad Bowl Finish Name is described by a number. Lower numbers are coarser than higher numbers. A good all around number to start with is grit. When you apply a stain or a finish to a raw wooden surface, you must first get the surface smooth and free of scratches or flaws. Start with a grit and increase to higher and higher grits until your surface is smooth to the touch and free of scratches and imperfections. When applying a finish, always sand between coats.

Use the same process described above. The object is to get a smooth surface that is free of scratches and flaws before you apply the next coat of finish.

With each successive coat of finish, you should sand with finer and finer grits. Wood stains change the tone or color of the wood veneer. One drawback to using stains is that they tend to dull down the luster of the wood. You can use a brush or a clean rag to apply the stain. Do some testing ahead of time. Wood stains usually darken the wood more than you expect. First, sand your wood veneer surface smooth.

Note: most of the veneers sold on this website are pre sanded at our factory and you may not need to do any additional sanding. Next, apply a coat of stain to the wood veneer using a rag. Let dry for a minute or two. Wipe off the excess stain with a clean rag. The longer that the stain stays on the surface of the veneer, the more it will darken the wood. Solvent based stains might penetrate through a paper backed veneer to the glue layer.

If you are using contact cement for your glue, this could loosen the contact cement. Let the stained surface dry for 24 hours before applying a finish. It is impossible to address all of the different types of finishes that can be used to finish a wood veneered surface.

For the purposes of this article, we will stick to wax, penetrating finishes, shellac, lacquer, water based polyurethane varnish, and petroleum based polyurethane varnish. Our two top choices for finishes: First: petroleum based polyurethane varnish. Second: Water based polyurethane varnish. Regardless of the finish, the wood veneer surface must clean and free of dirt, dust and contaminants.

The surface should be sanded smooth and free of scratches and defects. Most of the veneers sold on this website have been pre sanded at our factory and further sanding of the raw wood veneer surface may not be necessary. Note: When using a brush, don't skimp! Use a high quality brush when applying finish. Use a NEW brush. After all, you have put a lot of work and effort and pride into your veneering project. Its important to pay particular attention to the finishing process.

Types of brushes: Natural bristle brush - Use a natural bristle brush for solvent based finishes. Synthetic brush - Synthetic brushes should be used for water based finishes. Sometimes you will use a rag, such as when you apply a stain.

I even use a rag to apply my first coat of finish, first coat only, when applying a finish. Finishing wood veneer with wax is easy and you get a good looking surface quickly and easily. However, wax finishes give very little protection and successive coats of wax must be applied on a regular basis, forever. Apply the wax with a clean rag, let sit for a minute, wipe off. Buff if necessary. A rule of thumb: Two or three coats at first.

One coat a day for a week, one coat a week for a month, one coat a month thereafter. Getting a good finish using wax, stain, penetrating finishes and oil finishes is pretty easy.

The drawback to wax, stains, penetrating finishes and oil finishes is that the aren't durable. Getting a good finish using Shellac, varnish, or lacquer is tricky. Entire books have been written on how to apply a finish to a wooden surface. When using stains, wax, penetrating finishes or oil finishes, you may need to apply more than 1 coat. Use your judgment. When using shellac, varnish, lacquer, you will need to apply more than 1 coat.

It is usually necessary to apply at least 3 coats of finish shellac, lacquer, varnish, etc. Always let the finish dry completely before sanding between coats. Sanding between coats is always necessary when using finishes such as varnish, shellac, lacquer.

Sanding usually isn't necessary when using stains, waxes and oil finishes. Sand in the direction of the grain "with" the grain. Use a fine or very fine grit for sanding. If it is necessary to sand against the grain, be sure to follow up by sanding the area "with" the grain.

Some people use a fine steel wool pad.

Custom Brand Font Python Sliding Cabinet Door Brackets Iso Small Wood Project Plans Free