I also like turning wood boxes and people really love these. I might find the perfect piece of wood to get 10 or 20 boxes out of so I get all set up for that project, might take me 2 days or 2 weeks or a month but that’s what I focus on for a period of time. Woodturning ash wood mallet heads. Recently I found a nice straight ash branch and turned about 20 wood mallet heads. Then I decided to turn some handles.  One serving size yogurt containers are perfect to experiment with casting turning wood and resin projects. Storing and Using CA Glue For Woodturning. Since most woodturners use CA glue in some form, whether it be thin or thick CA you often get it in bigger bottles that the top gets clogged or the cap is lost causing all kinds of problems. (20) Woodturning - The Blue Planet.. a hybrid sphere - YouTube. Find this Pin and more on Woodturning by Wayne Creekmore. More information. (20) Woodturning - The Blue Planet.. a hybrid sphere - YouTube. Find this Pin and more on Woodturning by Wayne Creekmore. Saved from www.- Woodturning - The Blue Planet.. a hybrid sphere. Turning a hybrid sphere from a red mallee burl and blue epoxy resin I was contacted by someone who had seen a picture of the sphere that the 'hybrid ca Saved by Wayne Creekmore. I have made a wood turned sphere that is half wood, half resin. On the surface of the wood covered by resin, I CNC milled a texture made from a terrain model of Newberry Crater in Oregon. When you look through the clear resin, you can see the tiny model of the crater and the surrounding landscape. I used Yorkshire Grit to polish the sphere. resin: www.- yorkshire grit: www.- CNC: www.- wood turning tools: www.- Tools used in this project can be found at www.- To see upcoming p. No matter what type of resin you pick up, make sure you grab some disposable cups like these with the measurements on the side to mix the product in. To speed up the drying process, rough cut your blank slightly oversize and place it on a drying rack to allow airflow on all sides. The resin can make up the rest of the volume. That is why, we have compiled this list of the best epoxy resins in the market right now. This cannot wood turning wood and resin 20 understated! This is not to say that newer companies should be completely rejected.

My introduction to turning began with small projects. Turning wooden pens helped me learn basic skills, and I used some of the money from selling pens to fund my hobby. Before long, I started to buy resin pen blanks because of the amazing variety of colors that are available. It took a few years for me to realize the unique turning you can create by combining resin and wood.

A few exaples are shown above. It all started in northern California when I was taking a woodworking course at the David Marks school. On a trip to a local wood dealer, I saw some figured Claro walnut logs full of cracks and bark inclusions. I bought a log and took it back to my shop in Illinois, with no idea of how this beautiful specimen might be used. Then one night when I was turning a pen that contained resin and burl wood, it hit me: Why not combine resin and wood for larger-scale turning?

Control the cut. Resin is hard and dense, so you can expect to sharpen often and remove small amounts of material at a time. My biggest problem was lack of information—what resin to use, how to add color, how to Wood Turning Wood And Resin 70 get resin into cracks and inclusions, and so on. The Alumilite resin I use is available in different quantities. The pot is designed to be pressurized by an air compressor and comes with a gauge to help you maintain a safe pressure range.

Pressurizing the resin is essential for eliminating bubbles in the casting and forcing resin into all the cracks and crannies in the wood. There are two parts to the prep work you need to do: cleaning and drying.

Clean, then bake. I remove grit from crevices with a curved awl. General surface cleaning can be done with a drill and wire-brush accessory. Use compressed air to blow the blank clean. The mold will become part of the casting, and is cut away after the resin cures. I like to use melamine-coated particleboard MCP to make this type of one-time mold. MCP is inexpensive, readily available, and easy to work with.

Assembling the mold with hot-melt glue and screws creates a leakproof container for the resin. Make sure to remove the screws before cutting the mold free of the casting. A quick custom-made mold. The resin can make up the rest of the volume. Secure the wood inside the mold with glue or a screw to prevent the wood from floating when resin is added. I record wood and tinting details on the outside of the mold.

This eliminates confusion if I store the resin casting for any length of time before turning it. Plan to work quickly, because the Alumilite resin has an open time of just 12 minutes after Part A and Part B are blended. The resin is mixed by weight, but I need a volume estimate to get started.

I fill the mold with rice to establish the volume, then I mix equal weights of Parts A and B to create the total volume required. Mix with a drill and paddle, only until the Alumilite becomes completely clear. Then pour resin into separate pigment containers. Fill the mold as soon as your tinting is done.

Put in the pigment first. Mix the resin, mix the colors, then fill the mold. I use a drill and paddle mixer to blend equal weights Part A and Part B until the cloudy mixture turns clear. Then I divide the activated resin into separate containers containing my different pigments. Work quickly here, so you can fill the mold and put it under pressure before the resin starts to cure.

Putting the resin under pressure eliminates bubbles and voids; it also forces the resin deep into the wood. After placing the mold in my pot and securing the lid, I connect my compressor hose and add air until the pressure gauge reads around 60 psi. For a mold this size, I only need to keep the pressure on for about an hour and a half. Then I let the resin cure overnight. Remove the mold to free up the blank.

The resin will bond to the mold as well as to the wood inside. Remove all the fasteners in the mold, then cut the blank free. This can be done on the tablesaw or on the bandsaw, as shown above.

Resin casting offers creative possibilities that are limited only by your imagination and the size of your pressure pot. You must be logged in to write a comment. Epoxy is really prone to chipping at this low of speed, but I just had to get through this part before I could turn the speed up. After roughing out the outside of the bowl, I evened up the top of the bowl to get the bowl totally balanced on the lathe, then I could crank the speed up and start getting some nicer shavings.

I also went ahead and cut a mortise into the bottom of the bowl so the bowl could be mounted to the chuck later on. With the rough shaping done, I could really start to focus on cleaning up the chip out and refining the shape of the bowl. I used my Woodpeckers carbide turning tools for this project, and they were great at smoothing out the surface of the epoxy.

With the bowl as smooth as it was going to get with the turning tools , I moved on to sanding, working my way through the grits up to grit. Between each grit, I wiped the surface down with mineral spirits to remove the excess epoxy dust.

Once the finish was applied, I removed the bowl from the worm screw and mounted it to the lathe using the chuck. This is where things got a little frustrating. I proceeded a little more cautiously, with the tailstock in place to provide extra support, and starting clearing out the bulk of the inside of the bowl.

I was having a pretty hard time during this process, with the tool wanting to grab a lot, and I ended up launching the bowl again, but this time it did a little more damage.

It cracked the rim of the bowl, which I stabilized with CA glue off camera. I turned Wood Turning Wood And Resin Pdf my speed way up, somewhere between and RPM, which seemed like a good sweet spot for me. I was getting much better results at that higher speed, getting nice little shavings even though I was turning mostly end grain at this point.

I switched to the shearing cut to clean up all of the faces, which worked really well, especially on the epoxy, and then I could get back to sanding. I picked up one of these sanding wheels , which attach to a regular drill and speed up the process the sanding process quite a bit.

I moved up through the grits, going up to , and then switched to these sanding pads which I got from Rockler. They go all the way up to 12, grit, and are designed for acrylic and other types of plastic.

I worked my way up through the grits, wiping the piece down with a rag between grits, before applying finish. I went with simple wipe-on poly for this bowl, and it ended up working well. I kind of wish I had gone with a glossier finish, but I still think it turned out nice. Lovely bowl. American Woodturner Association will have a list of teachers near you.

Keep on turning! Nice effect, but what a waste of material, you Wood Turning Wood And Resin Filter could put a second container inside and pour out only the raw shape of the bowl. By craftedworkshop Crafted Workshop Follow. More by the author:. About: Weekly how-to project videos about woodworking, metalworking, and more.

Created by Johnny Brooke. More About craftedworkshop ». I made a few shearing cuts on the outside of the bowl to get them really nice and clean.

With the finish applied, the bowl was done! Did you make this project? Share it with us!

Center Square Woodworking Zone Best Wood For Turning Spindles 33 Buy Kreg Pocket Hole Jig 82