Radial Arm Saw Setup. Acheiving square, accurate cuts on a consistent basis. May 10, Question I am setting up a Delta radial arm saw for my brother. He wants to have an extended table and a good fence with an adjustable stop. He is having a problem with the saw coming out of square. Any ideas on how he can set this saw up with a good fence that produces accurate repeatability and is more consistently square? Forum Responses What Is Radial Arm Saw Used For Online (Cabinetmaking Forum) From contributor F: Radial arm saws are not known for extreme accuracy.  I use mine for rough cutoff and make my finish cut with a sled on the table saw. From contributor J: Ditto on the above post. Radial arm saws are notorious for holding their square setup for about three cuts. Radial Arm Saw Table Alignment -- an Easier Way: This is my 10" Craftsman Radial Arm Saw, vintage. It is very important that the arm is exactly 90 degrees to the fence at the back of the saw table. Note the square.  There's no such thing as being to safe in your workshop. Here are several ideas to make your shop safer. Tips and Jigs for the Shop # Radial Arm Saw Dust Collection Precision Control of the Dust. How to Replace the Table Surface on a Radial Arm Saw. The tabletop surface on a radial arm saw needs to be replacing when it becomes badly marred with saw cuts; here are the basics steps for replacing the tabletop. Garry Martin (@GarryMartin). The latest Tweets from Garry Martin (@GarryMartin). Detailed Radial Arm Saw guide that explains the benefits and uses. Find out why you need a RAS.  In this guide, I will tell you everything you need to know about radial arm saws, including what they are, what they are good for, and how they compare to both table saws and miter saws. What is a radial arm saw? Radial arm saw, as the name gives away, has its blade head attached to a hanging arm. In simple terms it is a circular saw that can slide along a pivoted arm. The same goes for the area behind the blade, too. Fence: Prevents workpiece from moving during crosscutting; guides workpiece across table for ripping. On some models there are two fences one set behind the other for ripping workwhile others have a single fence but two or more positions at which to locate it. Yoke Clamp Handle: Locks yoke in fixed position on arm; released to rotate yoke for ripping. Blade guards are essential: above and below and, when what is radial arm saw used for pdf, with adjustable antikickback fingers in place.

You can utilize it to Skip to content The Radial Arm Saw is essentially a circular saw suspended above a work table. Arm: Supports yoke, motor and blade. Yoke: Holds motor and blade; attached to the arm by a carriage unit with roller bearings that slide along a track underneath the arm.

Yoke Clamp Handle: Locks yoke in fixed position on arm; released to rotate yoke for ripping. Miter Clamp Handle: Locks arm in fixed position on column; released to swivel arm and set miter angle. Yoke Handle: Used to slide yoke along arm for crosscutting.

Bevel Clamp Handle: Locks motor in fixed position on yoke; released to set bevel angle or to move blade to horizontal position. Blade Guard Clamp Screw: Holds guard in fixed position; loosened to move guard.

Splitter: Keeps wood kerf from binding during a cut; anti-kickback fingers on each side of splitter prevent workpiece from lifting. Elevating Crank: Raises and lowers arm on column to set depth of cut. Stand: Supports saw; screw on feet are adjustable to level saw table.

Blade Guard: Protects operator from upper part of blade; nose tilts to cover leading edge of blade for ripping. Lower blade guard used for crosscutting. Column: What Is Radial Arm Saw Used For 36 Supports arm; four setscrews on front of column base and four bolts on rear of column tightened to prevent rotation. Rip Clamp Handle: Locks yoke in position on arm for ripping and for some cuts with blade in horizontal position; released for crosscutting.

Dust Spout: For dust collection system; adjustable nozzle directs dust away from work area. Arm Cover: Keeps dust from entering rear part of arm.

Miter Clamp Adjustment Screw: Turned to adjust tension on miter clamp; hole in arm cover provides access. Column Adjustment Bolts: Four bolts control amount of play between column and column base. Rear Table Table Clamp: Presses rear saw table and spacer flush against fence and front saw table. Auxiliary Table: Replaceable hardboard or plywood panel glued to front saw table; blade runs in kerfs cut in auxiliary table.

They say the radial-arm saw is difficult to adjust and, unless everything is perfectly aligned, makes cuts that are less than true. The radial-arm saw contingent argue that their favored tool is much more versatile than the table saw. They say it can sand and plane and, like the table saw, rip long boards at a single pass. So which is right for your shop?

Adjustment is crucial: Follow the instructions in your manual to the letter. It will also swivel right and left for mitering, and the blade and motor housing can be turned a full ninety degrees to right or left, meaning that the saw can be used to rip boards with the miter clamp releasing the yoke. For some operations, like ripping, the saw is fixed in place and the stock pushed through the blade.

The motor and blade can also be raised or lowered via a crank, either on the overhead arm or beneath the cutting surface. The saw will lock into any of these paths for precise work. Radial-arm saws are identified by the size of the blade for which they are designed. Like many table saws, most radial-arm saws use ten-inch blades.

The fixed worktable over which the radial-arm saw is suspended has a fence at the rear for holding work firmly in place. On some models there are two fences one set behind the other for ripping work , while others have a single fence but two or more positions at which to locate it.

An ideal position in a workshop for the radial-arm is against a long wall, more or less centered, with extension tables on either side of the saw. The fence should extend along the flanking tables, too.

Blade guards are essential: above and below and, when ripping, with adjustable antikickback fingers in place. Ripping is tricky and, if not done properly, can be dangerous on a radial-arm saw. If you use a molding or dado head, a shaper guard should also be in place.

A brake, too, should be in functioning order. The radial-arm saw can also be equipped with optional blades and accessories so that it can function as a drum or disk sander, router, or drill press. Even planer and jointer heads are available for some models. Check your manual or with the manufacturer of your saw to determine what options are available.

Rustic Wood Projects That Sell King Rockler Bench Vise Key