Just got a rip-cut and installed my Bosch saw haven't used it yet but saw was a good fit. I haven't even tried to make any angle cuts. Sign in to zrm In other words you redall to think a lot more when using a radial arm saw. Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion Craftsman Radial Arm Saw Recall Kit Work "buildsomething" web site which exclusively uses pocket hole construction. Sears radial arm saw recall image radial saw you are concerned with the material being held down on a table ar against a fence and pulling a blade towards you that reacts to such things as wood density, wood wetness and thickness and other sudden changes in the wood from such things as knots and cracks and defects unseen by your eye. Want to get updates on new answers?

I have a Craftsman Radial Arm Saw model no. M with a motor mfg. Good morning I can fully understand your interest regarding the age of your saw.

I will forward your question to an expert who will investigate the matter further and get back to you. You will hear from them within two business days if not sooner. Until you hear from us, have a nice day.

Thank you for your question. I looked up the model number you submitted. According to our records, this unit was manufactured April Please let me know if you need further assistance.

Thanks Henry and Mark in taking the time to answer my question on the age of my Radial Arm Saw, It is most appreciated. I am glad i could help. Worth every penny, as it rips and crosscuts smooth as glass.

The "parking area" behind the fence should be lower than the surface of the table. Your table should be topped with a thin layer of plywood so that when the blade is fed through the cut, the teeth actually cut an eighth inch or so into the thin layer of plywood. This also serves as a zero clearance slot for your blade to run in, which will reduce splintering. Thanks everyone for your knowledge of the RAS. I feel better about the problem being fixed when I install the new kit when I get it.

I don't ever turn any saw on until I am ready to make a cut. I make sure that I have the board where I want it and when I get ready to cut, I turn the saw on with the carriage behind the board and move it until the cut is made. I turn the saw off and I don't move the carriage until the saw blade comes to a complete stop.

I then move the carriage back to its position in the back. I then move the piece of wood I just cut. My dad told me never to stand in the line of any saw. I always stand to the side of the saw blade in case the blade kicks back which I never want to happen! Is that the correct way to cut a board to length?

I haven't even tried to make any angle cuts. The above is a You Tube with last part showing the retro fit of the craftsman saw. There are two parts on the same video showing the parts to the retro fit. Of particular interest is the method of how the carriage lock works with the retro fit.

Looks good to me. Thanks Jay for the link and all of your concerns with the RAS. I appreciate getting the "dos and don'ts" on the tools. I do try to stay safe. Like you said, if you don't think about it or don't know of the problem, you won't be looking for it.

Thanks for looking out for us beginners. I'd suggest replacing the RAS with a miter slide saw, and use it in conjunction with a table saw. Here is a picture of my retrofitted Radial arm saw. I just received my radial arm saw retrofit kit. I ordered it on May 4th and got it on May 24th. I haven't tried to put it together yet. I just opened the box to see what they Sears Radial Arm Saw Parts 40 sent me last night. I hope to try to put it together this week or next week. I haven't read the instructions yet. Was it hard to put together?

Why Sears Radial Arm Saw Recall Youtube did you add the hardboard? I hope you are enjoying the new retrofitted RAS. Thanks for the photo. I will post a photo when I get mine done. Thanks again for the information on the recall! Gary roofner said:. Thanks Jason. That makes sense. I'll make sure that I do the same. Jason Watkins said:. Yes I am very glad I purchased this saw.

I think I lucked into one of the best purchases in a while. The craftsman saws are known for their sloppy radial arm tracks but this saw is as good as my rockwell nice and tight.

I have been practicing making drawer joints using my dado set. United States 4 Items 4. Suitable For. Wood 2 Items 2. Not Specified 2 Items 2. Used 4 Items 4. Please provide a valid price range. Buying Format. All Listings 4. Accepts Offers. Buy It Now 4. Item Location. US Only. North America. Shipping Options.

Furniture Pulls 25 Inches Us Open Hardware Gpu Temp Editor Table Saw Extension Router Table Not Working