How to Replace File Cabinet Locks - www.-

Discussion in ' 2nd Gen. Tacomas ' started by MuddinfunJul 21, Log in or Sign up. Tacoma World. Welcome to Tacoma World! You are currently viewing as a guest! To get full-access, you need to register for a FREE account. USB port. Remove ignition lock cylinder Discussion in ' 2nd Gen. Post Reply. Joined: Apr 17, Member: Messages: 7, Apparently it's not documented anywhere on Tacomaworld, or youtube, or anywhere on the internet, how to remove the ignition lock cylinder from a 2nd gen Taco or a Camry of the same vintage.

After spending an hour trying to figure it out, I finally found the trick. This is like something out of an Indiana Jones movie. Every ignition lock since about has had the same removal procedure.

Turn the key to accessory and poke the pin with a paperclip. Well Toyota threw a trap into it. After you hear this, you can pull the lock cylinder out. To reinstall it, you just make sure the lock is turned to accessory and push it in. If you look close at this pic, you will see that I ground away the part where the 1st pin is that you push. I didn't have a key for this lock, and I wanted to use the lock cylinder.

After I ground it away, the lock pulled right out. So, here's how the trap works. As soon as you put the key in, it activates the trap. When you turn it to acc, push the pin, and pull, you can't remove the key. You can't turn it back to lock, and even if you could somehow get the key out, the trap is still activated. The problem happens when you try to remove the lock cylinder the proper way, and not with a grinder. The rod is poked in there to show where the hole is to deactivate the trap.

MuddinfunJul 21, BassAckwards05Taco4x4Weissenheimer and 5 others like this. Good information! JimmyhJul 21, Muddinfun [OP] likes this. I had to do this the other day and did not find a video. So hear is mine. Here's my question I drilled out the entire cylinder after it got screwed up from a theft attempt.

Horrible idea. I can not get it into the Acc position. I've heard you can sort of punch in the hole that releases it. In this case two holes Ctrott87Jul 20, If you can't get it to the remove file cabinet lock cylinder light position, at this point, your best choice would be to replace the whole assembly.

There are 2 breakoff bolts that remove file cabinet lock cylinder light need to spin with a sharp punch and a hammer. MuddinfunJul 20, This is timely I'm having issues with my tumbler sticking with my key. I have to rap it a few times with my knuckles in order to be able to turn my key. If this is like my focus Remove File Cabinet Lock Cylinder Quick I'll have to replace and key the lock to my keys.

TnroninJul 20, Weissenheimer likes this. Tnronin remove file cabinet lock cylinder light this. Ctrott87Jul 21, When the bolts are new, they look kind of like a double headed nail.

The top head has a hex. The bottom head is round. They tighten them up till the hex head breaks off. To remove it, you take a sharp punch and pound the edge, perpendicular to the bolt to spin it out. Ctrott87 likes this. I remove file cabinet lock cylinder light the hospital today and went to lunch. I had to ding the key quite a bit to get the key to turn. Once I got going I called a locksmith.

The hardest part to me was the sensor but it did come off with no issues. My holes are 3 and 9 o'clock. I had them rekey and make me a third key with no programing.

It's just a key to get in. I'll hide it someplace on the truck. Thanks for the info on removing the cylinder. Removing is just unscrewing the cowling remove file cabinet lock cylinder light separating from the steering shaft, top stayed on unplugging and disonnecting the sensor. Push the detent took some finagling. Went better than I thought.

I'm emotionally exhausted so that had some bearing on my energy levels. It had to be done. Remove file cabinet lock cylinder light can't be down a car at the moment. TnroninJul 21, Show Ignored Content. Tacomas Method Race Wheels Matte Black 16x8" 6x5. Motion Pro Hydraulic Brake Bleeder. Bilstein Shock Absorber. Stant Regular Locking Fuel Cap. StopTech Milliard Truck Tent Standard 6. Bilstein Monotube Shock Absorber, 46mm. Centric Parts Remove file cabinet lock cylinder light or email address: Do you already have an account?

No, create an account now. Yes, my password is: Forgot your password?

Just enter the lock code (found on the face of the lock core) and the manufacturer on www.- to purchase a replacement key. If you would prefer to change the lock core to use a different lock code (key), you can switch the lock core to another code within the same series. Mar 13,  · If you've ever broken off a key in a lock, you know how important it is to have a Broken Key Extractor on-hand. www.- offers a wide range of broken ke.

Cabinet Door Lock With Key Value Laminating Wood For Turning Bowls Youtube Router Sign Stencils Js Wood Shop For Rent Near Me Tonight