Porter-Cable (), User Manual

The Model and Serial No. Record these numbers in the spaces below and retain for future reference. This manual contains information that is important for you to know and understand. To help you recognize this information, we use the symbols to the left. Please read the manual and pay attention to these sections.

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may result in property damage.

Keep area well lit. Avoid chemical or corrosive environment. Do not use tool in presence of flammable liquids or gases. Do not wear loose clothing or jewelry. Loose clothing, draw strings and jewelry can be caught in moving parts. Rubber gloves and non-skid footwear are recommended when working outdoors. Wear protective hair covering to contain long hair.

Wear safety glasses or goggles while operating power tools. Also face or dust mask if operation creates dust. All persons in the area where power tools are being operated should also wear safety glasses and face or dust mask. Never carry tool by cord or yank it to disconnect from receptacle.

Keep cord from heat, oil, and sharp edges. Have damaged or worn power cord and strain reliever replaced immediately. DO NOT. Use clamps or a vise to hold work. Keep tools sharp and clean for better and safer performance.

Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and if damaged, have repaired by authorized service facility. Inspect extension cords periodically and replace if damaged. Have all worn, broken or lost parts replaced immediately. Keep handles dry, clean and free from oil and grease. Form habit of checking to see porter cable 4212 key keys and adjusting wrenches are removed porter cable 4212 key the tool before turning it on.

Do not carry a plugged-in tool with finger on switch. Be sure switch is off when plugging in. Keep porter cable 4212 key, body and clothing clear of blades, bits, cutters, etc. Watch what you are doing.

Use common sense. Do not operate tool when you are tired or while under the influence of medication, alcohol or drugs. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation.

A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual. Have defective switches replaced by authorized service center. Do not use tool if switch does not turn it on and off. Take extra care to prevent inhalation and skin contact when working with these materials. Request, and follow, any safety information available from your material supplier.

The purpose of this document is to provide you with an advanced knowledge of the jig and to promote that knowledge, along with your creativity, to produce Porter Cable Dovetail Jig 4212 Que beautiful woodworking projects that can stand the test of porter cable 4212 key. Use a plastic dead-blow hammer to join your workpieces together to help prevent the marring of wood Fig.

Chamfering the inner tail edges can make the joints go together easier and may prevent damage to the pins Fig. Make the chamfers with a file or a chisel. Since the chamfers are located on the inside of the joint, they will be invisible.

This method of setting your router bit Porter Cable Dovetail Jig 4212 Ge depth on through dovetails or box joints is very accurate for creating pins or tails that are flush, and is especially good for inlay work. Use a board that is the same thickness as your workpiece to be joined and draw a line. Set the router on the template and lower the router bit until it reaches the line. Make sure that the scrap material used in the horizontal position to support the template is at least as thick as the router bit depth-of-cut.

You can mount the jig templates to clamping boards and take the templates to the workpiece to make the joint. The benefits of this operation are:. You can maneuver a mounted template onto a large workpiece easier than clamping a large workpiece to the jig.

This process allows you to join boards wider than 12" by routing a part of the joint, sliding the mounted template just past the original cut, and routing the remainder of the joint. By using the clamping boards, you can rout boards that are too short to clamp in the jig base, allowing you to dovetail small decorative boxes. You can use both the normal through-dovetail template included with the Jig and the Accessory Kitand the miniature through-dovetail template included with the Accessory Kit with a clamping board.

Make a clamping board 2" x 3" x 19". Make sure that all four sides are square You may need to glue thinner sections porter cable 4212 key wood together and plane them to make the 2" board.

Drill the pilot holes for 10 screws on the face of the board as indicated in the drawing Fig. Align the lines of the porter cable 4212 key with the edges of the clamping board. You should be able to see the pilot holes in the elongated slot of the porter cable 4212 key Fig. Drive two 10 wood screws through the elongated slots of the template into the clamping board Fig.

Clamp the tail board with the outside surface facing away from the clamping board Fig. Porter cable 4212 key the tail board, using the instructions in your basic manual in the section. This step is optional. Clamp stop blocks to the clamping board for rapid setups of repeated cuts. Use a small square and a pencil to draw a line along the bottom of the clamping board Fig.

Align the line with an edge of the tail board. This line will be used to set up the pin board. Clamp the pin board with the outside surface facing away from the clamping board Fig.

Align the edge of the pin board with the line drawn in. Use the width of the tail board to make a pencil mark on the pin board for the depth 4212 Porter Cable 12 Dovetail Jig Al of the router bit. You can cut dovetails in boards wider than the templates mounted on clamping porter cable 4212 key by cutting the first part of the joint, sliding the templet down the workpiece, and cutting the rest of the joint.

Become familiar with the procedure for cutting through-dovetails with a template on a clamping board before attempting working with unlimited board width. Remove the half-blind depth bracket. Other than that, the setup is identical to the previous setup. If the board is a width in 1" increments, 12", 13", etc.

If the board is porter cable 4212 key in 1" increments, take the fraction of an inch that is greater than 1" and divide it by porter cable 4212 key. Unclamp the templet, slide porter cable 4212 key down, and center the last cut between the two straight fingers and reclamp Fig.

Unclamp the templet, slide it down, and center the last cut between the two angled fingers and reclamp. You can mount your half-blind template that comes with the and jigs and the accessory kit to a board.

This method, however, limits your workpiece width capacity to 8". These instructions can be modified for making halfblind dovetails with the through dovetail template and for the miniature dovetail template See the section.

Square porter cable 4212 key of the sides. Make a mortise through the board and drill pilot holes for 10 wood screws Fig.

You may need to use extra washers to prevent the bolt from sticking out. Make the straight clamping block. Make two thickness blocks the same thickness as the pin board. Drill a hole big enough for the wood screw to go through Fig.

Clamp the tail board drawer side to the main clamping board with the outside surface facing the board. Move the offset clamping porter cable 4212 key to the right until it touches the tail board Fig.

Insert the pin board drawer front flush against the tail board and the offset clamping block Fig. Slide the straight clamping block to the left so that it contacts the pin board Fig. Hook the straight clamping block over the front and back of the main porter cable 4212 key board.

Loosen the 10 wood screws, align the template lines with the line where the pin board and tail board meet, and retighten the porter cable 4212 key wood screws Fig.

You can use board-mounted templates with your router table.

PORTER-CABLE® has a proud history of power tool and pneumatic tool innovation. People of all walks have come to depend on and trust us to help them do everything from commercial and residential construction to woodworking. Discover why professionals have trusted PORTER-CABLE for over years. Explore our tools. Mar 01,  · I purchased a Porter Cable Dovetail jig for making drawers. the half blind template produced a flawless joint. The thru dovetail template however produced a joint where the front of the drawer was misaligned with the 4212 Porter Cable 12 Dovetail Jig Video Class side by roughly 3/64”.

Router Table Best 2020 Mod Whittling Tools For Beginners Score