Dust Collector Fittings | KenCraft CompanyKenCraft Company

Couplings allow you to connect pipe or fittings together without crimping. The coupling on the right in the drawing is a small-end coupling, and the ends will slip inside the ends of your pipe.

Die-stamped fixed elbows top elbows in the drawing offer a smooth, obstruction-free interior. There are two basic options you can choose from when you need to change pipe diameter. One option is to use a reducer like the one shown here.

Reducers are available in sizes ranging from metal dust collector fittings 90 up to 10"-to-9", in 1" increments. Go with a spun reducer instead of a welded one, as it has a smoother interior. Another reducer option is to use a fitting called a tee-on-taper. This creates less static pressure than using a tee and a reducer. Just like elbows, tees are available in many shapes and sizes. To minimize turbulence and reduce the chance of dust and chips settling in your ductwork, whenever possible you should use tees whose branches enter the main line at 45 degrees.

The tee on the right in the drawing is a 6"-on-6". Both are degree lateral tees. A wye branch allows you to split a branch line equally in two directions. The opening sizes can vary, such as 8"x4"x4" for situations where you want to split a large main line into two smaller branches. Economy wyes are often spot-welded together; industrial wyes have a continuous weld at each seam.

A swivel-ball joint is designed to connect a pipe to pipe or pipe to flexible hose while allowing it to pivot. HVAC transitions like the round-to-rectangular shown here are quite handy for shop-made pick-ups or dust hoods. Attach the end of a flexible hose to one of these, and you can press it into service as a pick-up for a lathe or even as a simple bench- top or drill press dust catcher.

This setup works great as a pinpoint dust catcher for a band saw, scroll saw, or drill press. Although most folks think of a floor sweep as a great way to clean up the shop and it isyou can also use one next to a machine where sufficient dust metal dust collector fittings 90 can be difficult such as a drill press.

Floor sweeps are available with or without a door. Blast gates are used to control the airflow within a whole-shop dust collection system. There are three main types of blast gates available: full blast gates, half gates, and self-cleaning gates. Although blast gates are most often used to control the air flowing to a machine, they can also be used to balance the air going from one branch to another.

You can install half gates in existing ductwork with out having to disassemble the ducting. You cut a slot halfway through the duct and slide the half gate metal dust collector fittings 90 place.

The blade of the half gate is cut round to match the diameter of the ducting. The gate is held in place with blind rivets inserted though the casting and into the existing ductwork. Half gates cost about the same as full blast gates and come in sizes from 3" to 16". Full blast gates are available in either metal usually cast aluminum to keep weight down Metal Dust Collector Fittings Network or plastic.

Metal blast gates usually have a screw that you can tighten to lock the gate open or closed. To allow airflow to pull the blade tight to the surface of the casting, metal dust collector fittings 90 the gate so that the screw is pointing in metal dust collector fittings 90 5 Inch Dust Collector Fittings direction of airflow. Self-cleaning blast gates are particularly useful in shops that machine either green wood or highly resinous woods that tend to stick to and clog up a gate.

On a self-cleaning blast gate, the shutoff blade is longer, and there's a T-shaped rubber gasket on the end of the gate metal dust collector fittings 90 right photo. To clean the Metal Dust Collector Fittings Zero gate, loosen the two nuts near the gasket so that you can pull out the gasket.

Then push the extra-long blade completely through the casting to clear out the chunk. Quick View. Add to Cart. You must be logged in to write a comment. Log In. Find a Store. My Account.

My Cart. Go to Home Page. Mobile Navigation. Same Day Shipping Find a Store. Search Go. Topics Cabinetry. Choosing Hardware. Dust Collection. Friends of Woodcraft.

Getting Started with Woodworking. Make Something. Pen Kit Reference Chart. Press Releases. Resin Casting. Shop Talk. Woodcraft Magazine. Woodworking Metal dust collector fittings 90. Couplings Couplings allow you to connect pipe or fittings together without crimping.

Reducers There are two basic options you can choose from when you need to change pipe diameter. Tees Just like elbows, tees are available in many shapes and sizes. Wye branch A wye branch allows you to split a branch line equally in two directions. Swivel-ball joints A swivel-ball joint is designed to connect a pipe to pipe or pipe to flexible hose while allowing it to pivot.

Transitions HVAC transitions like the round-to-rectangular shown here are quite handy for shop-made pick-ups or dust hoods. Floor sweep Although most folks think of a floor sweep as a great way to clean up the shop and it ismetal dust collector fittings 90 can also use one next to a machine where sufficient dust collection can be difficult such as a drill press.

Blast gates Blast gates are used Metal Dust Collector Fittings to control the airflow within a whole-shop dust collection system. Full blast gates Full blast gates are available in either metal usually cast aluminum to keep weight down or plastic. Quick View Item Write Comment You must be logged in to write a comment. Learn More. Customer Care Talk to a friendly customer care representative to help with your purchase. Talk to an Expert Get advice on the latest products and help with your projects.

Sign Up. Connect With Woodcraft. Accessibility Options.

39 rows · Jul 04,  · Additional shipping charges will apply: Under $ will be charged an /5(16). Typhoon offers elbow connectors in both 45 and 90 degree angles both for making a slight bend in a branch line or a full degree bend. NOTE: Fitting-to-fitting joints use outside couplers, while pipe-to-pipe joints use inside couplers. Dust collection fittings come in many sizes and shapes. Find the best selection of blast gates, T fittings, Y fittings, 3 way fittings, reducers, union fittings, swivel fittings, ports and port caps, flanged fittings and many more options/5.

Carpentry Workshop Tools 800 Mallett Hammer Corvette 10 Tapered Dining Room Table Legs Quiz