Dovetail Router Bits. If your workshop is oddly shaped or you work in two smaller rooms, it's better to have two smaller filters than a big one. Contact An Expert. The Lowdown On Jet Air Filtration Filter Size Values Dust Separators. Remember me.

Saw Accessories. Power Feeder Accessories. Morticer Accessories. Sander Accessories. Power Tool Accessories. Router Accessories. Drill Accessories. Rotary Multi Tools. Multi Tool Accessories. Multirip Saw Blades. Rip and Crosscuts Saw Blades.

Saw Blades for Non-ferrous Metal. Dry Cutter Saw Blades for Steel. UltraThin-kerf Saw Blades. Saw Blades for Portable Machines. Saw Blades Accessories. Jig Saw Blades. Universal and Fast Wood cutting. Fine cuts wood, laminates and plastics. For ferrous and non-ferrous metals and plastics. Sabre Saw Blades. Cutting wood and construction boards. For construction wood, nonferrous metals and plastics. For metal sheets, pipes and profiles.

Cutting bricks and porous concrete. Blades for multipurpose saws. Universal arbor. Arbor for Festool, Fein. Arbor StarLock. Blades for Scroll Saws. Bandsaw Blades. Roundover Cutter Heads. Chamfer Cutter Heads. Joint Cutter Heads. Universal Cutter Heads. HW standard carbide knives. Double-edged beveled. HW special carbide knives.

Cutter head accessories, knives and HM standard carbide knives. Straight Router Bits. Rabbeting Router Bits. Roundover Router Bits. Chamfer Router Bits.

Dovetail Router Bits. Round Nose Router Bits. Glue Joint Router Bits. Wainscot Panelling Router Bits. Window Sash Bit Set. Kitchen Router Bit Sets. Profile Decorative Router Bits. Straight Router Bits with Reversible Knives. Rabbeting Bits with Reversible Knives. Roundover Bits with Reversible Knives. Chamfer Bits with Reversible Knives. Spiral Router Cutters. Spiral Flush Trim Bit. Diamond Straight Router Cutters. Diamond Flush Trim Bits. Router Bit Accessories. Collet chucks and adapters.

Dowel Drills for Mafell. Drills for Domino Festool. Drills with quick change shank. Multi-purpose Holesaws. Bi-Metal Holesaws. Diamond Dry Holesaws. Center Drills and Accessories for Holesaws. Dowel Drills. Dowel Drills for through holes. Hinge Boring Bits. Dowel Drills with threaded shank. Kitchen Worktop Jigs. Straight Guide Clamps.

Router Table Accessories. Universal Hinges Boring System. This will create a pretty good draft and some noise for others in the basement. The air would be pushed towards the area I want to protect. The biggest problem that I see with this choice is the Jet would be pulling air from the entire basement which could possibly reduce the effectiveness. To add another twist, the ceiling height is only 7'5" and the Jet is 12" high.

I'm tall enough to hit my head but I need clearance for moving stock and not block light. Tags: None. Odd you should ask this just now, because I'm wondering the same thing myself as I iron out the final details of the power plan for my new shop building.

Most of the installations I have seen in magazine photos or on the Internet have the filter hanging more or less out in the middle of the room, perhaps cheated toward the area where the bulk of the dust is produced. That seems to make sense, and so I was planning to locate a ceiling outlet at the appropriate location.

In my case that was centered across one direction of the shop, but a couple feet off center the other way. If the object is to filter ALL the air in the shop, this seems to make even more sense than a central location.

So, further investigation is needed, something I've not yet had time to do. If I find anything more, I'll post it here. Last edited by LarryG ; , PM.

Reason: clarity. Comment Post Cancel. I have hung the cleaner from the ceiling with the intake facing my table saw and router. The intake is about four feet from the out-feed side of the saw and about seven feet from the floor.

I have had the unit in place for about two years. While the unit does not prevent dust from reaching into all corners of the garage, it does reduce the problem. Its most noticeable effect is to clean the air relatively quickly and effectively as judged by the accumulation of dust on the pre-filter and my lack of reaction to airborne dust. I also use a Jet dust collector, with one micron canister, and the two devices Jet Air Filtration Filter Size Number work together to produce an almost dust free environment.

I also use a face mask when cutting or routing MDF and for most sanding. My guess is that you are not going to prevent ALL the dust from reaching into the far corners of the basement, but you should be able to stop most of it. Good luck, Steve. Added Note: Larry makes a good point about air circulation. In my case, there is a fair amount of air circulation and I find the air cleaner useful in distributing warm around the garage when the heat is on.

I neglected to note that the air cleaner is just a little off the middle of the room. Last edited by steve-norrell ; , PM. Larry and Steve, Thanks for your info, the comments about airflow circulation was helpful. I'm going to place it a little off center of the room about 4' from the edge of my shop with the intake facing the shop. Then create a cloud of dust and see what happens. Thanks again, Brian. I think you've gotten excellent advice for placement of the unit.

I'm just going to add that a shop vac that can accommodate a bag most Shop-Vac brand and many Ridgid units can do a lot to prevent dust from becoming airborne. It might not get everything that your routers generate, and might only get half from your miter saw, but whatever it DOES get has no chance of swirling around in the air.

Diy Woodworking Bench Top Mini Table Legs Wooden Ikea 4 Types Of Hand Planes Round Do It Yourself Wood Wall Decor Water