The JET® JWBSSFX, 14" Steel Frame Bandsaw redefines the line between functionality and affordability in the wood bandsaw category.  This saw is equipped with JET’s easily adjustable blade guide system, makes adjustments quick and simple. The JET 14” Bandsaw also features over 13 inches of resaw capacity, and dual 4 inch dust ports for maximum dust collection efficiency. Heavy duty tubular steel welded construction, robust stamped steel doors with welded steel pin hinges, and heavy duty base, allows for stability and durability when sawing large work pieces. The JET 14” SFX Bandsaw provides the woodworker all the premium features of a higher end saw with superior performance to complete any project. Features. Jet JWBSOS instruction manual and user guide. Device Category: Construction Tools. Device Group: Bandsaw. Brand: Jet. Model: JWBSOS. Title. Pages. Обзор ленточнопильного станка (Wood Cutting Bandsaw) JET JWBSQ.

Table Of Contents. Quick Links. Operating Instructions and Parts Manual. Table of Contents. Previous Page. Next Page. M Ph. Page 2: Important Safety Instructions Do not use this band saw for other than its and other substances known to the State of intended use.

If used for other purposes, JET California to cause cancer. Avoid inhaling dust disclaims any real or implied warranty and jet 14 bandsaw review manual Page 3 Check damaged parts. Before further use of Turn off machine before cleaning. Use a brush machine, a guard or other part that is damaged or compressed air to remove chips or debris — should be carefully checked to determine that it not your hands. Page 4: Table Of Contents Page 5: About This Manual Additional knowledge can be obtained from experienced users or trade articles.

Whatever accepted methods are used, always make personal safety a priority. If there are questions or comments, please contact your local supplier or JET. JET can also be reached at our web site: www. Page 6: Specifications 4. Page 8: Setup And Assembly Read and understand the entire contents of this manual before attempting assembly or operation. Failure to comply may cause serious injury.

Figure hardware package Box 1: Stand not shown 5. Only hand tighten screws at this time. Figure 5. Take measurements at both front and back of table — these should be identical. If miter slot is not parallel to blade, bump table with rubber mallet in the needed direction. Page Jet 14 bandsaw review manual Screw Improper connection of the equipment-grounding conductor can result in a risk of electric shock.

The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor. Page Voltage Conversion Zero setting of cursor cannot be used with horizontal fence position. Figure 6. Remove dust block C, Figure Carefully remove blade from top wheel, then from between upper and lower blade guides and lower wheel. Slide blade out through slot in table. Guide new blade through table slot.

Place blade loosely in upper and lower blade guides. The blade performance. Tip: When the band saw is not being used, raise tension lever to release position — Page Upper Thrust Bearing jet 14 bandsaw review manual. Refer to Figure The thrust bearing prevents backward deflection of blade during cutting.

Disconnect band saw from power source. Loosen screws M, Figure with 3mm hex wrench and raise guard plate to expose thrust Figure blade guide adjustment bearing.

Page Guide Post 7. However, belt tension should be occasionally checked when the band saw is new, as a new belt may stretch slightly during the breaking- in process.

Page Operating Controls gauge for a crosscut, the fence should be 8. Turn on band saw and allow a few seconds for 8. Press green button to start. Press red paddle button to stop. Page Crosscutting 9. Page Width 9. Set patterns are usually tooth. Page User-Maintenance Clean band saw jet 14 bandsaw review manual to remove any resinous appropriate capacity. See our website for a full line deposits and sawdust. Keep miter slot and guide bearings clean and free Periodically vacuum out the motor fan cover.

Page Blade Selection Guide Tighten lock handle. Trunnion locking mechanism is broken Replace trunnion locking mechanism. Reduce feed force. Blade pitch too coarse. Refer to blade selection chart; use finer pitch blade. Guide bearings jet 14 bandsaw review manual properly supporting Check guide bearings for correct blade.

Adjust or replace as needed. Page Mechanical And Electrical Problems Non-proprietary parts, such as fasteners, can be jet 14 bandsaw review manual at local hardware stores, or may be ordered from JET. Some parts are shown for reference only, and may not be available individually. Power Cord Jet Logo with Adhesive Wood Insert Socket Head Button Screw Lock Washer Push Stick, Red Hex Nut Adjustable Handle Hex wrench not shown Page Electrical Connections Print page 1 Print document 36 pages.

Cancel Delete. Sign In OR. Don't have an account? Sign up! Restore password. Upload from disk. Upload from URL.

Related Manuals for Jet JWBSSFX. Saw Jet JWBSDX Operating Instructions And Parts Manual. inch deluxe band saw (28 pages) Page 1 www.- document is bookmarked Operating Instructions and Parts Manual inch Woodworking Band Saw Model JWBSSFX Shown with optional lamp kit # New Sanford Road LaVergne. Two of them rated it a 4 out of 5 stars. The third one had good things to say about it, except that it was underpowered. I imagine that this particular model doesn't sell very well, because the next model in the Jet bandsaw lineup only costs slightly more and has some added benefits. That brings us to the 14" JWBSCS Jet bandsaw. It appears to be made from the same "chassis" as the open-stand model . Item number Description Literature; A: JWBSOS, Bandsaw with Open Stand: Manual: K: 14" Closed Stand Bandsaw, 1HP, 1Ph, /V: Manual: K.

Kreg Joinery System As Seen On Tv 01 Laguna Belt And Disc Sander Zoo German Lathe Chucks