If you use your saw properly and only for what it is intended, you will enjoy years of safe, reliable service. Lockthe for cross cut travel by checking the blade against the table and the miter indicator. Rcaftsman the inner craftsman radial arm saw manual graph washer, saw blade, outer blade washer, and blade nut on the blade arbor. Radiaal in two carriage covers, one on each side of the arm. Visit the Craftsman web page: www. Table of Contents.

Sight visually check proper alignment spreader with saw blade as shown. If the spreader not aligned, adjust it as follows Page 20 locations and functions of controls versatility Radial is due, in part, to its controls, and these are the keys to its successful operation. Learn to use the controls all operations before actually starting to saw. Page 21 Proper Indexing Method Experienced operators bevel lock lever locks motor to the yoke woodworking equipment, such as this Craftsman Radial when motor is in position.

Pull lever Saw, acquire habit indexing in one direction release and push to lock. Arm control lever must be in locked position. Adjust the antikickback assembly Guard spreader and antikickback mechanism must properly set. Page 27 Since the work is pushed along the fence, it must have a straight edge n order to make sliding contact with fence. Also, New Craftsman Radial Arm Saw 50 the work must make solid contact with table, so that it will not wobble.

Provide a straight edge, even t this To adjust, remove the set screw with wrench shown. Use the bevel lock lever as a wrench to tighten clamp bolt. The arm should snugly on the column. If not, then adjust. Remove 2 screws from rear cover The lock action should feel tight and secure. Considerable amount of effort must be applied to the lever to lock Page NOTE: Changing one adjustment will effect another, so it is best perform alignment procedures when correcting any one problem.

Dull blade or warped board. Avoid attempted use of severly warped material. Do not lubricate between radial arm cap and radial arm. When receive your Craftsman radial saw, requires no lubrication. Page 26 I! Page 44 Fig. Page 53 Keep extra blades on hand, so that sharp blades are always available, Gum and wood pitch hardened on blade will slow it down, Use Craftsman Gum and Pitch Remover No, 9.

Page 58 I! Print page 1 Print document 64 pages. Cancel Delete. Sign In OR. Don't have an account? Sign up! Restore password. Upload from disk. Upload from URL. Page 11 Throw-Back Resin Saw throwing back a workpiece similar to kickback. A sticky, sap-based substance. Through Sawing Rip Cut " In a radial saw, a cut made with the blade parallel to AnyCutting operation where the blade extends completely through the workpieca.

Page 12 Check a ll loose parts from the box with the list below. Use the instructions on the followingpages to assemble. Allfasteners are shown actual size. Saw Assembly Page 13 Check a ll loose parts from the box with the list below.

Use the Instructions on the followingpages to assemble. All fasteners are shown actual size. Saw Assembly not shown Page 14 Check all loose parts from the box with the Craftsman Radial Arm Saw Key Keyboard list below.

All fasteners are shownactual size. Leg Stand Table Support A. Table SupportRails Page 15 Thefollowing toolsareneeded f orassembly andalignment. They arenotincluded w iththissaw. Page 18 motor, blade, and blade guard and can be pivoted with all operating features and safety requirementsof so the blade faces right,front, or left.

It is located below the handle. See Figure 9B. See Figures 9A-9D. Contained in two carriage covers, one on each side of the arm. See Figure 9C.

See Figure 9D. When you remove the saw and hardware insert levelingfeet intothe Craftsman Radial Arm Saw Parts bottom of the legs. See Figure Ignodngthis precaution to keep the saw from tipping,walking,or sliding. Install the yoke assembly from the front of the arm. Remove the blade and blade guard assembly during The table supportsare a base for the three wooden table sectionsand fence. The bevel lock lever is preset at the factory but may need readjustmentafter shippingor extended use.

Check for overtightnessor looseness and make any neces- sary adjustmentsas follows: The bevel lock lever is locatedon the frontof the yoke See Figures 20A - 20D. If you can movethe arm inner column tube is snug in the housingand to remove any looseness. Press the arm to the side. If there is play between the column support and the column tube, it needs to be adjusted.

See Figure 20B. If not, adjustthe table See Figures 22,4 and 22B. Use this procedure to installthe fixed fronttable. The top of the table has counterboredholes, preddlled from the top, around the center to attach the table. In the center are a counterbored hole and a small hole, which is not counterbored.

They are used for raising or loweringthe center of the table until it is level. If there are any high or low areas on the front table, they should be removed by adjustingthe leveling The placement of the tables and fence may need to screws in the center holes on the front table.

Place the inner bladewasher, saw blade, outer blade washer, and blade nut on the blade arbor. See Figure26A. Note: The concave side of blade washers go againstthe blade. See Figures 27A - 27C. Move the the blade to ride in the middle of the kerf and keep it yoke back untilthe blade touchesthe fence. Page 37 Release the arm lock knob. See Figures 29A - 29C.

Best Router For Bosch Router Table Tennis Radial Arm Saw Workbench Plans Queen Garden Project Ideas 01