Craftsman Radial Arm Saw Motor Part No. Motor Model No. C48BC | eBay

Table of Contents Section Title Repair Parts If within one year from the date of purchase, this Craftsman Radial Saw Guard Kit fails due to a defect in material or workmanship, Sears will repair it, free of charge. Severe cuts, and loss of fingers or other body parts due to contact with the blade. Radia, impact injuries, and blindness, from being rdial by a thrown workpiece, workpiece chips or pieces of blade, 3. Bodily impact injuries, broken bones, and internal organ damage from being hit by a thrown workpiece 4.

Shock or electrocution 5. Major Hazards Three major hazards are associated with using the radial arm saw for ripping, They are ouffeed craftsman radial arm saw 63607 full hazard, kickback, and wrong way feed.

This section only briefly explains these hazards. Read the ripping and crosscutting safety craftsman radial arm saw 63607 full of your saw manual for more detailed explanations of these and other hazards. Safety Symbol and Signal Words An exclamation mark inside a triangle is the safety alert symbol. If you reach around the blade to the outfeed side when ripping, and try to hold down or pull the workpiece through to complete a cut, the rotational force of the blade will pull your hand back into the blade.

Fingers will be cut off. Read and follow all safety information and instructions. When a workpiece kicks back, it could hit hard enough to cause internal cdaftsman injury, broken bones, or death. Wrong Way Feed Hazard Wrong way feed is ripping by feeding the workpiece into the outfeed side of the blade. The rotational force of the blade can grab and pull the workpiece.

Before you can let go or pull back, the force could pull your hand along with the workpiece into the blade. Fingers or hand could be cut off.

Wrong Way Craftsman radial arm saw 63607 full. Regular eyeglasses are not safety goggles. Wear close fitting clothes, short sleeved shirts, and non-slip shoes.

Tie up long hair. Do not wear gloves, ties. These can get caught in the spinning blade and pull body parts into dae ravial. Wear dust mask to keep from inhaling fine particles. Wear ear protectors, use saw daily. Keep children, pets, and visitors out of 6307 area; they could be tilt by a thrown workpiece, workpiece chips or pieces of blade.

Turn saw off, remove yellow key, and unplug before leaving work area. Do not leave until blade has stopped spinning. Make work area child-proof: remove yellow key to prevent accidental start-up; store key out of sight and reach; lock work area. Keep floors clean and flee of sawdust, wax and other slippery materials. Keep work area well lighted and uncluttered, craftsman radial arm saw 63607 full. Use saw only saaw dry area.

Do not use in wet or damp areas. Keep them in working order. Repair or replace damaged parts before using saw. Unplug saw before doing maintenance, making adjustments, correcting alignment, or changing blades. Do not force rasial. Use saw, blades and accessories only as intended. Before turning on saw, clear table of all objects except workpiece to be cut craftsman radial arm saw 63607 full necessary fixtures, clamps, or feather-boardso.

If blade jams, turn saw off immediately, remove yellow key, the free blade. Do not try to free blade with saw on. Do not layout, assemble, or setup work with saw on, or while blade is spinning. Keep saw table clean. Store items away from saw. Do not climb on saw or stand on saw table to reach items because saw can tip over.

Cut only one workpiece at a time. Stacking or placing workpieces edge to edge can cause user to lose control of workpieceo. Safety 636607. Rip only workpieces longer than craftsman radial arm saw 63607 full diameter of the blade. Do not rip workpieces that are shorter than the diameter of the blade being used. Workpieces that extend beyond the saw table can shift, twist, rise up from the table, or fall as they ar'e cut or afterwards.

Support workpiece with table extensions the same height as the saw table. To prevent tipping, support outer radiaal of extensions with sturdy legs or an outrigger.

Do not use another person to help support workpieces or to aid by pushing or pulling on workpieces, because these actions can cause kickback. Use table extensions. Use clamps or vice to hold workpiece. Do ssw overtighten blade nut because blade collar could warp 6o Do not turn saw on and off in rapid sequence because blade craftsman radial arm saw 63607 full loosen.

Blade should stop within 15 seconds after saw is switched off. If blade takes longer, the saw needs repair. Contact Sears Service Center. Use only 10" or smaller diameter blades. Use blades for their recommended procedures. Keep blade sharp and clean.

I B Rear Table 40" Izront Fable 40" I E Tahte Supporl Handle Assembly Bag Ol Loose Parts I Conlaining: I I. Adapter Motor Key Bag Ol Loose Paris Assembly Guard screws, Installation existing Steps table gull. Keep all including the lev1. Remove Note: boards This retro fit guard behhM are being supplied kit requires fence, additional clearance New table. Discard the old table boards craftsman radial arm saw 63607 full keep the fence.

Install board. Refering to your saw owners manua! Remove the front table. The U-Clips that were used as nuts for the rear screws must be moved to the new screw location Remove them from the saw craftsman radial arm saw 63607 full reinstall them on the table.

Referring to your saw owners manual, install and level the table boards. Remove crosscut travel may no Ionger to your saw owners tlavel. Rotate the saw craftsman radial arm saw 63607 full the outrip position. Remove and discmd ttle oflmr lmndle retaining screw, Discard tile old handle, 8. This locks tile adapter in place. Lock motor at 0 bevel blade vertical. Position guard so riving knife fuces front of saw.

Blade pinching is a cause of kickback, 1. Lock yoke in in-rip position blade towards column, motor towards front of arm. Lower arm until blade just clears table, 3. Unlock rip lock while holding up lower plastic guard, move yoke back until blade touches fence. Lock rip lock. Lower riving knife to the table and tighten knob.

The riving "knife should rest fiat against fence, 5. If adjustment is needed: 1o loosen riving knife bracket screw. Z slide riving knife so it rests against fence. Frees radial arm to craftsman radial arm saw 63607 full locks in any desired position; pro-set indexed positions at 045L, 45R Turns motor on! Insert into on-off switch Remove after turning saw off Move towards right to unlock, towards left to lock Support motor before unlocking because it can swing down quickly.

Craftsman Radial Arm Saw Motor Part No. Motor Model No. Condition is "Used". Motor runs smoothly and has no known issues. Cable is in good shape. We will unscrew the power cable clamp from the case and place it into a plastic www.- date: Feb 05, Download the manual for model Craftsman radial arm saw. Sears Parts Direct has parts, manuals & part diagrams for all types of repair projects to help you fix your radial arm saw! Craftsman tool box full of USA tools $ (Salem) Craftsman Heavy Duty 10" Radial Arm Saw $75 pic hide this posting restore restore this posting. $ favorite this post Mar 8 CRAFTSMAN 10 In. RADIAL ARM SAW Craftsman 10" Radial Arm Saw .

Soft Close Drawer Slides Repair Cost Computerized Wood Cutting Machine Form Lathe Turning Tools Indexable Carbide Insert Use Glue Up Wood For Turning 40