Packard Woodworks: The Woodturner's Source: Oneway 24'' Lathes

Safety First Do not attempt this project if you do not practice proper shop safety at all times. This project may appear dangerous but with proper precautions you can lessen the possibility of injury. I take no responsibility for the accuracy and completeness of this instructable. I am not responsible 36 wood lathe guidelines you building this instructable and using it in an unsafe manner, proceed at your own risk. Note: With the hole in the centre of the end 36 wood lathe guidelines, it's offset from the blade and higher than the blade.

If the blade were set at it's highest position it could not come in contact with the bearings 36 wood lathe guidelines the metal threaded rods. Your saw blade location and height may vary, it's up to you to locate the holes in 36 wood lathe guidelines plywood so as to not contact the saw blade, threaded rod and drill. Use the 36" of hardwood stock and cut it to fit the tracks of your table saw.

My saw has recesses at the bottom of the tracks and I shaped the wood to fit the shape of the tracks. This will reduce any upward force the saw blade would have on the revolving wood blank. Fasten the wood runners to the plywood base. Ensure you countersink any fasteners used on the runners so they do not scratch the tracks on your saw.

I hope you are a visual learner. Put all the pieces of wood together to make an object similar to the pictures shown. You need 4 bearings. I had an old skateboard on my shop wall that no one had used in some time so i harvested the bearings from it. Hint, You might be surprised at what you have around the house that hasn't been used in awhile either. Take a length of the threaded rod, sharpen one end, but not to sharp, place 4 nuts, 2 washers and 2 bearings on the rod, see the picture.

Drill a hole in the center of the end boards. Drill a hole to recess the bearings. Place the threaded rod, nuts, washers and bearing in the end boards as shown. Take a length of the threaded rod, place 4 nuts, 2 washers and 2 bearings on the rod, see the 36 wood lathe guidelines. Drill 2 holes in the center of the wood blank.

One to 36 wood lathe guidelines the tail stock, the other to fit the t-nut. Place one end of the wood blank into the tail-stock, screw the other end into the head-stock. Tighten the nut closest to the head-stock first, then tighten the second to to the first one. Then tighten the nuts on the outside of the box and the head-stock. Ensure the whole apparatus once tightened can be freely turned by hand, this may take 36 wood lathe guidelines adjustment.

Place a drill on the head-stock and using at medium speed turn the blank, see video. Raise the blade of 36 wood lathe guidelines saw so it just touches the wood blank then raise it a bit more. Go slow, in all it took 5 passes to create a round dowel. Sanding - If you are right handed, reverse your drill and use your left hand on the drill and your right hand on the sandpaper.

Don't press to hard or you could twist your wrist. I used 80 grit sandpaper and then 36 wood lathe guidelines the roughness of the sandpaper. The first dowel I made was of softwood so I would reduce any possible damage to my saw.

I had some hardwood glued up and my next dowel was a short hardwood one. This is where I realized I need a "wobble" board to reduce the wobble in the threaded rod. If you want to make short dowels you will need a "wobble" board within 2" of the wood blank.

Also 2 more nuts tightened to the t-nut. I would suggest you make long dowels and then cut them to length. Reply 3 years ago. Reply 2 years ago. For safety purpose, you should put an "end block" to stop 36 wood lathe guidelines trail so you can't push it too much and touch the blade with the drill or worse Thank you for the feedback and taking the time to comment.

I might use your idea to improve on the safety of the apparatus. A plexiglass shield would also be an easy safety measure should the stock get loose and fall into the blade. All that said what a great solution for the need of a large dowel.

Introduction: Table Saw Wood Lathe. By ledgehead 36 wood lathe guidelines. More by the author:.

About: Hi More Laguna Wood Lathe Prices Canada About ledgehead ». Participated in the Epilog Challenge 9 View Contest. Did you make this project? Share it with us! I Made It! Incredible Wooden Spirals by rschoenm in Woodworking. Reply Upvote. Yonatan24 Georgejb75 Reply 2 years ago. Direct link to one of the youtube videos. SinAmos 3 years ago. Clever idea and a very simple project. Chuck 3 years ago. Thank you for taking the time to comment and your ideas to improve safety.

rikon 20 x 36 inch Variable speed lathe. NEW! powermatic MODEL C 20" X 42" PRO Wood Lathe. New Model Of Our Most Popular Lathe! Baileigh WLVS 20 x 60 Woodworking Lathe. NEW! laguna 24|36 24 x 36 inch lathe 3HP V - 3 HP. NEW! powermatic MODEL B h.d. 24" X 42" Wood Lathe. Craftsman 36 Inch Wood Lathe Origin by: ken It is Craftsman, originally made by Duracraft. Rigid also sells the same lathe different color. Mine is a Duracraft with the Sears copy crafter attachment, Rigid number WL, can't remember the Craftsman model #, start by Googling Duracraft lathe and you'll come across a ton of info. REVO 18 - 36 Lathe, V, HP. 30x40 VSR Lathe with Sliding Bed. 24|36 REVO Lathe 3HP V. 14 x 40 Benchtop Wood Lathe Model JWLVS. PM Lathe, 1 HP, V. Nova Comet 14DR Lathe Bundle. Mini Lathe Model Short Bed Lathe, Model PM Lathe with Lamp Kit .

Jwds 1020 Benchtop Drum Sander Uk Open 10 In Saw Blades For Table Saws Case Marking Knife Paul Sellers Github