Shop Dust Collection & Air Filtration at Rockler

I'm planning on building more than a few cabinets for an upcoming kitchen and bath remodel, on my house. My overhead track is 20' long. Lifting capacity is about lbs based on the PEG 4 trolly capacity. The additional hose eetup keeps the air and vacuum hoses from getting tangled up.

This would make a great setup to extend your wood shop fun to a ripe old age. There is no reason an electric hoist couldn't be used. I started by taking the HF dual suction cups to pieces. Then I carefully scored the estup on top of the cups with a razor knife and with a little additional cutting I was able to remove the inner metal disks.

I wound up clamping the rubber just to be sure I had good adhesion. I glued some 1" wood dowels inside the handles of the suction cups with epoxy resin to reinforce them. Then I assembled the cups while discarding the plastic levers. I initially tried using rubber cement do glue the disks back together, but something went wrong with my ability to wait for it to dry before putting together. These suction cups are not able to lift plywood without doing the mods and using a vacuum pump, They are capable of lifting non porous materials, such as glass.

The suction cups and manifold are attached to wood shop vacuum setup on mac 2' length of Unistrut. The suction cup handles can Wood Shop Vacuum Setup Machine be attached with 1. I have a truss roof in my workshop and I did not want to vacjum wood shop vacuum setup on mac the chords. I spot welded the track together where the 2 pieces met. The trolly body is made up of a couple of pieces of scrap aluminum channel bolted to either side of the 2 Unistrut wheeled trolleys.

With the middle bolt going through the eye of the hoist. I initially was a little over enthusiastic with my welding and had to spend an extra hour or so unwarping the sidewall of the strut where I joined them together. I needed some way to contain the vacuum hose for the lifter and the air hose for the hoist. So I slit two 10' lengths of 4" drainpipe on my table saw and using a short piece of 3" schedule 40 pipe as the trolly. I used two 20' foot lengths on either side of the hose trolly, as the hoses have trouble stretching to 20', the vacuum pump is on wood shop vacuum setup on mac end wood shop vacuum setup on mac om compressed air for the hoist is on the other.

The green cable in the picture is necessary to drag woood trolly from a parallel direction. The drainpipe is secured to the lower chords by wood screws with fender washers.

I used a wireless remote control electrical outlet to turn the vacuum pump on and off. I made this, but I need help understanding how you got good suction to the plywood.

How exactly does the suction apply eetup the rubber? A good solution for lifting heavy sheets. Reply 5 years ago on Introduction. I swear that wasn't there the first read through, but sometimes I miss Wood Shop Vacuum Setup 700 really obvious things.

This is a very interesting idea, I have been thinking of something similar for lifting heavy sheets of 25mm MDF. By elking In the Shop with Scott Follow.

More by the author:. The additional vaucum trolly keeps wood shop vacuum setup on mac air and vacuum hoses from getting tangled up This would make a great setup to extend your wood shop fun to a ripe old age.

Materials required your milage may vary : Harbor Freight 2. Wireless remote control electrical outlet, to turn the vacuum pump on and off. Various nuts bolts and screws. Participated in the Metal Contest View Contest. Did you make this project? Share it with us! I Made It! Gary 2 years ago. Reply Upvote. I love your shop. It' beautiful. Wood shop vacuum setup on mac much potential in a space like that. Kinnishian mikeasaurus Reply 5 years ago on Introduction.

Plus, maybe it was edited in. AaronD15 5 years ago on Introduction. Constructed 5 years ago on Introduction. Ian 5 years ago on Introduction. Mindmapper1 5 years ago on Introduction.

Working in the shop with the floor covered in sawdust and woodchips is dangerous too. Tripping over piles of wood debris, slipping on sawdust and shavings, stepping on screws and nails lost in the clutter are all hazards that exist in a dirty shop. Delaying cleanup is also a fire www.- of dry wood shavings make excellent tinder, and a stray spark can easily cause a fire. www.- : woodworking vacuum system. Cen-Tec Systems Quick Click 16 Ft. Hose for Home and Shop Vacuums with Expanded Multi-Brand Power Tool Adapter Set for Dust Collection, Silver. out of 5 stars $ $ 63 ($/Ft) $ $ Get it as soon as Wed, Mar The Shop-Vac system consists of eight clear 3' pipes (24 linear feet), five couplings to join the pipes, four "T" connectors, six blast gates, two 90º elbows and three 45º elbows, ten mounting clamps, along with sufficient wall plugs and screws to mount the system to your shop walls.

Plasma Cutter Wood Templates Solution Wilton Bench Vise For Sale 60