I was reading about Envirotex lite and find different directions for the stir times to mix it. If the finish is low-solids and penetrates, then the surface of the wood becomes the surface of the finish, with all its grain patterns and qualitt. You wood projects resin quality have noticed that when you cast epoxy, you can sometimes dent your fingernail in the finished casting if you try hard enough. Instead of using resin, have you thought about just using a different adhesive for the wood projects resin quality We used a blue translucent tinting pigment in our resin to achieve the watery effect in our table. Long article. Scrape the sides of the cup and the bottom to get a fully even mix, otherwise, the resin won't set as it should.

The most noticeable change is in respect to color. When UV light hits a resin coating, it degrades the epoxy polymers, causing ambering i. Even resin that may have started out crystal clear will soon turn a yucky yellow hue.

This process and outcome is inevitable, however there are things that can be done to the chemical make-up of the resin formula to mitigate this. Many epoxy resins on the market include a UV stabilizer aka UV inhibitor to help protect against yellowing, as well as other problems that epoxies are prone to such as de-lamination, chalking, cracking and gloss loss.

In truth, a UV stabilizer is necessary and effective, except when it comes to the yellowing issue. A UV stabilizer merely delays yellowing somewhat HALS has been demonstrated in numerous test cases over the years to be extraordinarily effective in protecting against yellowing —there is approximately 50 years worth of this evidence available Google it!

ArtResin was developed specifically for use over artwork and craft projects, meaning it has been formulated to keep artwork beautiful and as the artist intended, over time.

Any resin product that does not include both HALS and UV stabilization will, as a matter of scientific fact, amber and yellow over a period of a few months to a year typically. Now it is ready to hang up. This allows for air bubbles to come up and create little voids in the surface resin to reveal what color is underneath.

Once on the board, lift up to release the resin and watch the colors ooze apart. Question 7 months ago on Step 1. Answer 2 months ago. Use a heatgun. It disperses the heat more evenly and you have more control. I'm not sure but resin may be flammable. Question 2 years ago on Introduction.

Introduction: Resin Art For Beginners. By ChrisJ Follow. More by the author:. Plastic Disposable Cups - I don't use a cup more than once, so buying some cheap plastic party cups work best.

Large Popsicle Sticks - These are for mixing the resin and also mixing the paint into the resin, for this, I use one per cup since I don't like to be constantly mixing colors. Plastic Sheath - I use gallon trash bags, but buying those would probably cost more than buying some plastic sheeting to make a nice work area that won't ruin your countertops. Latex Gloves - For protecting your hands from the resin.

Did you make this project? Share it with us! I Made It! Pirate Treasure Hunt Game by mrdebos in Cardboard. I have used epoxy in boat building and wondered if the epoxy I used would be suitable for such work. Does anyone have any suggestions as to a resin product suitable for use in wood turning?

Martin Cramer Alberta, Canada. Last edited: Aug 10, Martin Cramer said:. Click to expand I have uses System 3 and West Systems in my turnings for years. Marilyn Campbell uses it in almost all of her pieces. I mix all sorts of colors, inks, paints, powdered paints, and dyes.

Mix a test before you use any of these because some won't mix and some change the chemical structure so it won't cure or loses strength. Most alcohol based dyes and inks will mix. I've used some water based paints and some oil based. Powdered paints work well and thicken it as well so it can be pretty handy for filling. For smaller holes in knots I mix Ink but leave the epoxy kind of transparent. That way it picks up the color of the wood as well as the color the I put in it.

I just picked up what I need to do an article on mixing Gold Leaf with epoxy for some cool affects. Keep your eyes on the magazine. Thanks for the advice, I'll have to do some experimenting. I tried coloring some West Systems with some water based aniline dye power and used it to fill some flaws. It worked but the resulting color wasn't very vibrant and I think the dried epoxy was a little softer than normal. I was wondering what gave those bright saturated colours I've seen in photos.

Now I have an idea where to start. I haven't used any yet but have achieved some pretty bright colors using paints. The problem I've run into using paints is if you use too much it changes the epoxy and it may not cure properly. Too little and you may not get the brightness that you want.

If you get the West Systems epoxies get yourself a digital scale. For a Small Wood And Resin Projects lot of what I do I don't need a full pump using their pump system. So I squirt about what I need of the epoxy into a dixie cup. Weigh it. Then divide by either 3 or 5 depending on the hardener your using.

This gives you the amount of hardener you need. That way I can mix up just exactly what I need. It's also really handy to weigh when your mixing paint into it so you know exactly how much you used.

You can make this a percentage or ratio so that you can mix the proper amount of paint next time. Weight sounds like a great way to accurately mix small quantities.

I had pumps for a boat building project but they seemed impossible to clean in order to reuse some time down the road. Time to do some experimenting. Steve Worcester Admin Emeritus. John King. Joined Aug 31, Messages Likes 63 Website www. Most commonly used are powders such as tempera paint or chalk line dust, but there are many other options available.

Dry powder pigments are best for coloring epoxy because you can add as much as you want. Tempura dry powder paints are excellent to pigment the epoxy. Another option is our Graphite Powder will turn the epoxy black, add 1. If you have any other questions feel free to let us know. Thanks John Your website has been very useful over the years. I dye my epoxy black with just a few drops of Alcohol shoe dye.

It works great and I can make it anywhere from jet black to translucent smokey depending on how much I use. Richard Coers. Anyone ever seen old pieces of these works using epoxy? I thought I read where it breaks down with ultraviolet light exposure. I also wonder about wood movement over the years, and with it imbedded in a brittle material, is there minor cracking?

I expected a perfect polish, but you could see some abrasive marks or maybe you could call it course rubbing compound marks. I expected it to look like glass, but maybe too tough to do in the black tinted epoxy..

Marking Knife Means Of Door Pivot Hinge 83gn Uk Wood Cnc Machine For Sale Nz