WATCO Danish Oil. Уникальная смесь глубоко проникающих масел и лака. Материал является очень простым и совершенным средством полировки деревянных поверхностей, позволяющим произвести окрашивание, лакировку и защиту за 1 нанесение. Масло наносится без особых усилий, и придает особый вид деревянным поверхностям, обычно достигаемого только после длительной ручной полировки. За счет глубоко проникновения в поры древесины тонирующие масло защищает поверхность от растрескивания, хрупкости и шелушения. Цвет: Классический орех (арт). Главная → Масла • лаки → Масла → Watco → "Датское оригинальное" защитное тонирующее масло WATCO Danish Oil. "Датское оригинальное" защитное тонирующее масло WATCO Danish Oil. Документация: Тех. документация. Масла, воски, полироли для дерева. Масло Датское тонирующее защитное Watco 0,л натуральный. Проблема с изображением? Фотографии покупателей  Датское тонирующее защитное маслоWATCO Danish Oil. Уникальная смесь глубоко проникающих масел и лака. Твердеет внутри дерева, а не на поверхности. Watco danish oil application journal is a simple process of curing any finished oil. This brand of Danish oil is available in many colors and it provides professional-looking results. Cindy, To avoid changing the color of the wood, you want to avoid oil-based finishes altogether. My Danish Oil says to wait hours between coats. Appplication applying to make sure that sanding is completed and your surface of the wood is smooth. Danish Applicztion application method two — the one coat a day method.

After another hour we wiped the board again, although there were no obvious signs of surface oil at this stage and the board was dry to the touch, with a pleasant low sheen finish. The board was left at room temperature for 48 hours before it was used to allow the Danish oil to cure.

The particles should then be removed with a very fine grade wire wool oooo grade. The performance of Danish Oil will continue to improve naturally for a week or two after application. We recommend that wood should not be subject to heavy use, and any water or other spills should be wiped off immediately during this time. Note: This method allows Danish Oil to penetrate deep into the timber, naturally waterproofing and nourishing when using our Tung Oil based product.

This method is suitable when working on large areas, or when there is a limited amount of time available for oiling each day. To show this method, we again took an untreated oak chopping block. We applied Danish Oil liberally until the block stopped absorbing the oil. The block was then left for 20 minutes before all excess oil was removed with a clean reg. Application during the second day was the same as the first.

Danish Oil was applied until the wood stopped absorbing. After 20 minutes all excess oil was removed with a clean rag. Day three involved the same process again. After 20 minutes the excess oil was removed with a clean rag. The photograph below was taken at a low angle to show the low sheen finish after application and finishing with Danish Oil.

This method allows any nibs or dust to be removed with very fine grade wire wool or fine abrasive paper between coats of Danish Oil if necessary. Skip to content We recommend two different methods of applying our Danish Oil. Surface Preparation As with any coating, surface preparation is extremely important in getting a satisfactory end result. By this stage the oil was not soaking in very much and the block was looking really wet, with an obvious coating of oil on the surface: After another 20 minutes we returned and removed all the remaining Danish Oil from the surface with a clean rag: The board was left for one hour and then wiped over again to remove any oil that might have exuded back out of the pores of the wood.

Danish Oil application method two — the one coat a day method. Improperly disposed oily rags can spontaneously combust. Hang them outside to dry in a safe area or spread them out flat. They should not be in a pile. Once they cure, the cloth will be hard and brittle and you can throw them out.

Question 2 years ago on Introduction. Can I soak new cut plywood scroll saw pieces in Danish oil overnight? Or, dipping it in a tray for 30 minutes? Question 3 years ago on Introduction. Hello and thanks for the video information. My question is I noticed that you did not sand between coats, is it necessary or not? I am making an unfinished acacia wood butcher block, L-shaped bench for my breakfast nook that will be built-in.

We want something to seal it with something that does not change the color much, yellow like polyurethane and not a glossy finish.

We would like to keep it as close as we can to its natural color, maybe a matte or satin finish. We will sand and seal the wood prior to building in a shop, and prefer not Watco Danish Oil Application 64 to do much sanding in our home now and in the future.

We would like some advice Thank you so much for your time! To avoid premature evaporation, I decant the oil into smaller bottles, in which I aim to have as little air as possible. A hassle, but before I switched to this method, I lost half a tinfull due to over-long air contact. Reply 5 years ago on Introduction. Thanks for the Watco Danish Oil Application 50 comment. The process I described is commonly called the 'one day' finish - flood it one and come back reapply successive coats in the same day, then wiping it off.

Another way to do it is to wipe on a thin coat, then come back the next day in 8 hours or whatever and do another thin coat. In my experience both work well. I don't generally put finish back in the can - I try to one take out a bit at a time to make sure I'm not wasting any.

Thanks for the tip on evaporation, good to know! Reply 3 years ago. I know this is a really old comment, but thought I would share a tip for any new people stumbling over this great instructable.

Instead of moving the oil over in smaller containers, it is possible to fill up the can with marbles. This will fill up the empty space and thus removing the air in the can. The marbles can than be washed when they are no longer needed. I've never used Danish oil to finish my projects because I didn't know how it worked and how it looked. I'll give it a try now with more confidence! Introduction: Applying Danish Oil. By Donjek Follow. More by the author:.

Wait a day, and the piece is ready for use. It's that easy!

Baseball Bat Blanks For Sale Nz Cnc Router Machine Operator Zoom 48 Inch Oak Dowel 82