See My Vises For Sale. Look for any cracks or damage to the front and back of the jaws which might pose a problem. Then I glued neodymium rare earth magnets woodworkong place, ensuring that they were slightly below the surface of the wood. I Made It! Share vintage columbian woodworking vise 5g with us! The vise is now reassembled.

I buy and sell some of my collection and can even do vise restorations. Most vises are sold on eBay but I have a select stock of vises which are prime candidates for restoration and are for sale through this site.

See My Vises For Sale. How do I restore a vise? There is no better feeling than to restore a vintage bench vise to like-new condition. Part of the attraction for me to vises is the quick and easy restoration process which leaves me with a sense of accomplishment. Restoration Tips. The most common and versatile vises, the bench vise serves mechanics, machinists and tinkerers alike.

Typically offered in 3" - 8" in jaw width some larger examples can reach 10" wide jaws and over pounds. Generally designed to be mounted to Vintage Woodworking Vise For Sale Tower a mill or lathe, the machinist vise are usually precision Vintage Columbian Woodworking Vise Question made tools that demand a high price at sale. Many swivel and some even has 3 axis of movement. A less precise version of the machinist vise, the drill press vise is about holding parts for drilling only. Designed to be mounted under a work bench, the jaws are typically made from soft wood and can be easily replaced.

This allows clamping of wood without leaving marks on the work piece. A wood vise on steroids! The pattern vise allows several more degrees of movement. The jaws swivel as well as the entire vise can be rotated above the table making this the transformer of vises.

Used to hold water pipe for threading and cutting, the pipe vise is a plumbers best friend. While not as collectible as bench vises, some older examples are truely beautiful and well made. Since my work bench was 1. You will need another person to assist with the next few steps.

Before drilling any holes, ensure that the vise fits flush with the front and top of the bench with the "filler" plywood in place if your bench is less than 2". I had to move the plywood back from the edge of the bench and also router a slight curve to the plywood to allow for a slight curve to fit the front jaw machining.

I lightly sanded and then stained the front of the plywood to make it blend in better with the bench. Then I marked the drill holes on the plywood and tacked the plywood in place on the underside of the bench to ensure proper placement.

After drilling pilot holes for the LAG bolts, I drove them with washers into place, securing the vise to the underside of the bench. Then I drove two 12 x 2" long wood Vintage Wilton Woodworking Vise Version screws through the mounting holes at the top of the back jaw face, into the edge of the bench. The vise is now secured on the bench. I decided to use Frog Lube Paste to lubricate the vise. White lithium grease is a more common option. I lightly coated any vise surface that rubs against any other vise surface: the main screw threads, guide rods and the area around the cotter pin.

Then I glued neodymium rare earth magnets in place, ensuring that they were slightly below the surface of the wood.

Note: if the magnets are placed too deeply into the wood, they will not have the force needed to stick to the vise face. Allow proper time for the glue to completely dry. The magnets are more than strong enough to hold the plywood in place, but can be removed by simply pulling them off.

Can someone describe how to secure this vise? Reply 1 year ago. John - if you look at the pictures in step 5 and 6, that should help. Basically, the vise will mount under your bench with the top of the vise flush with the top surface of the bench. On the model shown, there are slots for two bolts to anchor the vise to the bottom of the bench. You did great job I also have a old bench vise that I am going to clean up and restore I am not sure of the brand but did See 70 also mine is a quick release that looks very close to yours.

Thank you. That design of vise is really nice. If I can help with your restoration, please let me know. Late last year I bought a 7 inch Richards-Wilcox quick release vise at a second hand store. Due to expedience I put it in service immediately and have have gotten good use of it since. Your wonderful restoration and excellent instructable have inspired me to attempt a restoration of my own.

Thank you so much. Reply 4 years ago. By ksjunto Follow. More by the author:. No further vise disassembly is required. Then I marked the drill holes on the plywood and tacked the plywood in place on the underside of the bench to ensure proper placement After drilling pilot holes for the LAG bolts, I drove them with washers into place, securing the vise to the underside of the bench.

Enjoy your new wood vise. Did you make this project? Share it with us! I Made It!

Woodworking Supplies Veneer 81 Wood Carving Kit Reddit 2020 Jet Plane It Up To The Sky Review Best Woodworking Shop Plans Us