Weights - optional cast iron wings : 16kg each. Connect the saw to an electrical circuit that is protected by a 20 amp breaker. Miter slots T-shaped: 19mm at top, The lower elevation limit has now been set. Page Saq The Blade Guard Note that since the spreader extends above the top of sawstop contractor table saw pdf blade it cannot be used as a riving knife, even if the top guard and the fable pawls are removed, as shown in Fig.

Universal Performance. All-purpose versatility, reliability and safety for a variety of users. Is the Contractor Saw Right for You? Compare Saws. Get All of the Tech Request a Brochure. Follow Us on Instagram. See More Contractor Saw Videos. Shipping dimensions saw body only : 35" W x 30" D x 20" H. Shipping weight approx. Weights - table saw only: lbs. Weights - optional cast iron wings : 35 lbs each. Blade: tooth, prof. Blade diameter: 10". Blade tilt: Left. Blade kerf 0.

Blade plate thickness: 0. Dado diameter: 8" req. Dado max. Main bearing size: 62mm OD x 30mm ID. Second bearing size: 52mm OD x 25mm ID. Table in front of blade max. Table behind blade max. Arbor Runout: 0. Table flatness measured diagonally: 0. Blade alignment with miter slot 0. Alignment between splitter and blade: 0. Insert: zero clearance, phenolic core, melamine surfaces. Belts: V-ribbed belt — static dissipative. Overall saw dimensions 30 in: mm W x mm D x mm H.

Overall saw dimensions 36 in: mm W x mm D x mm H. Overall saw dimensions 52 in: mm W x mm D x mm H. Use only recommended accessories with the saw. Consult this manual for recommended accessories. The use of improper accessories may cause risk of injury. When servicing, use only identical replacement parts. Keep the top of the saw clean and free from clutter. Cluttered areas invite accidents. SawStop saws are the only saws smart enough to know the difference between you and the wood you are cutting.

The use of smaller diameter blades with a brake cartridge designed for larger blades could result in a serious injury because the brake cannot be positioned correctly to stop the smaller blades. Page 15 Similarly, stacks of two or Delta Contractor Table Saws Year more 10 inch blades should never be used on your SawStop saw as the combined weight of the blades may be too heavy to stop quickly.

Attach the legs to the front pack 1 and hardware pack 2. Do not fully tighten the nuts. Repeat this process to attach the remaining short bracket E between the rear legs. Page 20 There is one hole in each corner of the stand see Fig. Adjust the panels until the holes align and then tighten all of the nuts in the stand using a 13 mm wrench.

The stand is now fully assembled. Page 22 Fully tighten all of the nuts using two 13 mm wrenches. Page Installing The Elevation Handwheel Open the blade tilt package and slide the handwheel onto the tilt control shaft and then thread the tilt lock knob onto the shaft see Fig. CNS Serial No. Mount the left extension wing with four M8 lock washers and four M8 x 16 hex screws, but do not tighten.

Note: You must install a rip fence prior to using the saw. Refer to the manual accompanying your rip fence for instructions on how to install the fence. Page 29 Arbor Block Sawstop Contractor Saw Dimensions Key Fig. Never operate the saw without the table insert in place. Do not use table inserts with metal or other electrically-conductive parts that could contact the blade. This can cause the brake to be activated unnecessarily.

Other sizes or types of blades are not compatible with a SawStop saw. Page 33 see Fig. Then move the riving knife slightly toward the right to clear the positioning pins, and lift it out of the clamp. Use the blade guard and spreader for every operation for which it can be used, including all through-sawing.

Page 35 Note: when using a dado set, neither the blade guard nor the riving knife may be used. Instead, use other protective devices such as push sticks, push blocks and featherboards see page 54, 82, 84 and Page Dust Collection SawStop recommends the use of a dust collection system that provides at least CFM of flow at the dust port. Attach a 4 inch diameter flexible hose between the inlet port on your dust collector and the port on the dust shroud see Fig.

Page Electrical Power Connection Do not use any other motor to power your saw. Connect the saw to an electrical circuit that is protected by a 20 amp breaker.

To use V power, you must purchase a SawStop V contactor box assembly and follow the installation instructions that are provided with it. Only after the V contactor box assembly has been installed on your saw should you begin re-wiring the motor.

Make sure the saw is unplugged from the wall outlet before proceeding with the following instructions. Locate the contactor box which is mounted to the back side of the switch box bracket see Fig. Page 41 see Fig. Page 42 see Fig. A wiring diagram Green is shown in Fig. These limit stops are pre-set at the factory and should not need adjustment.

If you decide to adjust the blade tilt limit stops, see page 66 for instructions. Page 45 An audible click will indicate that the thermal overload switch has been reset and the saw is ready to use. Double check the electrical circuit and all electrical connections and always use an appropriate feed rate for the material that you are cutting. Page System Status Codes System Ready — this code indicates that all self-checks have been completed, the safety system is operating properly, and the saw is in Standby Mode ready to run.

Page Using Standby Mode. The brake will not be activated and the code will automatically clear within 5 seconds after contact is ended. The system will not allow the motor to start while this code is displayed. Page 48 The overload error indicates that Sawstop Contractor Table Saw For Sale the system was close to firing the brake before it went into overload. Therefore, repeatedly attempting to cut a wet piece of wood could result in an unnecessary activation of the brake.

Page Using The Blade Guard Note that since the spreader extends above the top of the blade it cannot be used as a riving knife, even if the top guard and the anti-kickback pawls are removed, as shown in Fig. Page 50 When not in use, the blade guard can be stored by hanging it on one of the storage pins on the left side of the saw see Fig. Page 52 Do not touch the portion of the workpiece that was cut off until the blade stopped. Never make free-hand cuts.

Never hold or touch an unsupported piece of wood while the blade is spinning. To reduce the potential for kickback and a serious injury, move the rip fence out of contact with the workpiece when cross-cutting to prevent the workpiece from binding between the rip fence and the blade. This fence system can be used with optional 36 or 52 inch extension tables. Page Rip Cutting See page 82 for instructions on making Delta Contractor Table Saw With Unifence a push stick. To reduce the chance of a serious injury, always use a push stick or push block when your hand comes within 6 inches of the blade.

Page 56 Fig. Although not shown in the illustration, a second featherboard can be clamped to the top of the table and against the left side of the workpiece to hold the workpiece against the rip fence. Page Using The Saw In Bypass Mode If that occurs and the saw is started, then the shard could contact the aluminum brake pawl and cause the brake to activate.

Rockler Pen Turning Video Editing Veritas Marking Knife Kit Wood Shop Dust Collection Layout Bottom Mount Soft Closing Drawer Slides Android