Skip to the beginning of routwr images gallery. See top rockler router fence 50 of table for layout of channels. I am taking it further though to add all the other goodies to it. The oversized dust chute provides maximum dust collection efficiency. See how you can get free standard shipping. The redesigned arbor lock lever eliminates the need for two wrenches, and is easily accessible from above the table.

Be sure Rockler Router Fence Data to use cabinet grade plywood or better quality for flatness and select all your wood that is as straight as possible. Keeping the legs square to the outside corners and centering the middle leg assembly to the plywood base. Predrill the holes to avoid splitting. Attach two swivel casters in the middle. Use four lag bolts per caster and add a lock washer and a washer to each lag bolt. Flip table over and attach long beam supports between leg assemblies with pocket screws.

I was able to clamp a block of wood under the long support to hold it flush with the top of the leg assemblies. Here is how the supports look finished. Cut out the top corners where the end beams and middle beams are with jig saw. Below I am screwing the partition in to the bottom of the table. You will also be able to screw into the top support beam as well. Attach the second plywood workbench top the the top of the first plywood workbench top with wood screws from underneath.

Be sure the keep screws out of the path of the router channels for the T-Track. At this point the table is all built and ready to use.

I am taking it further though to add all the other goodies to it. Cut out table saw hole with circular saw and jig saw. Measure out the size of your table saw top and cut it to fit that size. Use tape to protect the edge of the plywood. Cut out corners to wrap around the legs. Assemble shelf and supports with screws. Cut out hole for table saw dust to fall into. That way the table saw still has something to sit on. I jacked up the shelf and clamped it in place so I could screw it in underneath.

I also squared it off and screwed it in through the partition. Rout out miter gauge outfeed channel in workbench top. Rout it long enough to get the miter past the blade of the table saw.

You want the channels to be deep enough to keep the top of the T-Track flush or just below the surface of the table top. See top view of table for layout of channels.

This is where the T-Track intersections will go. Cut out router lift hole with router at the depth of the lift plate. Start routing in the middle and work your way around in circles until you get to the edges. At the edges I clamped down wood as bumpers to keep my lines nice and square. Sand and polyurethane table top. I sanded with grit sand paper. On the outside edges I used an orbital sander to remove all the print on the boards and level the two top layers together.

After I sanded I brushed in four layers of scratch resistant polyurethane. I also sanded with grit sand paper between coats. I wanted it to be a really nice smooth surface. I started with the intersections then cut the T-Track to length with a metal blade on the jig saw. This part was fun because it was all coming together.

Level the table saw with shims. I gave myself some wiggle room to be able to shim it up to the right height Rockler Router Fence 10 of the table top. I got it nice and flush with the top. Install router lift adjustment screws. I installed four of these adjustable screws around each corner of the router lift for fine tuning the lift to the table.

I had to go to the hardware store and pick these up. Once these are installed, all you need to do with this screw is reach under the table to level out the router lift flush with the top of the table. You should only have to do this once when you first install the lift. Here is a picture of the screws and how they are installed.

Drill a hole for the nut and screw it in with an Allen wrench. Then reach under and make the fine tunes adjustments to the level of the lift. This is a longer version of the two screws that came with the lift.

I added the nut to a longer screw that matched. The nut gets hammered into the bottom of the table, so it would clamp the lift on really tight. This is how it ended up. Nice and flush. I clamped the vise in place and pre-drilled the holes to make it easier to screw in. Build a block for the the vise. Glue them together. Drill three holes for the three bars of the vise to slide through.

Sand and polyurethane the block. Remove the two big nuts at the end of the vise. Install the block of wood you just made over the three bars of the vise.

Now I need to take the time to find out what tools go where and customize the spaces under the table for them. I also have plans to build the doors like I mentioned in the design. I will have to let you know how that goes in the near future. Let me know if you have any good suggestions about how you organize your shop and what has been working well. I would love to hear your feedback! Cassity started Remodelaholic with her husband, Justin, to share their love for knocking out walls together.

I have been everywhere around me and can only find treated lumber or cedar post. Love the plan! Does the base have enough strength? Seems to me with only the plywood bottom base, and no cross bracing, there would be some bend in the plywood.

I have not seen any bend in the plywood base. I had plans at one time to add a simple rectangular frame under the base for added support.

Thanks for asking. I really like the table, purchased the plans to make one. What kind of router works with the lift? I had to Rockler Router Fence Quad make my own collar. But it is hard to get in and out. I need to explore other router options. Great looking bench, and lots of great functionality!

I have searched for some time and keep coming back to this one as the most viable for my space, with some minor modifications for example, I have an older Craftsman table saw with external motor, which will require a different solution for the center support in that area — not a major issue. The latest update to the popular PM series—features a hydraulic mobility kit and a DRO for precise blade angle adjustments!

Item Skip Rockler Router Fence Grid to the end of the images gallery. Skip to the beginning of the images gallery. Out of stock. Ships directly from the manufacturer. View Shipping details. See how you can get free standard shipping.

This item will ship directly from the manufacturer. Must be shipped within the 48 contiguous United States. Please allow up to 7 business days for your shipment to be prepared. Additional shipping charges may apply and will be noted below the price.

Items shipped by truck are delivered to the curbside only. Please call customer service before returning product.

King Canada Belt And Disc Sander Online Woodworking Projects End Tables Zoom Grizzly Combination Belt And Disc Sander Image Wood River Skinner Knife Kit Manual