As for anchoring, the lift plate sits on several grub screws, and I never felt a need to anchor it down beyond gravity and friction. OK Cancel. Reply 5 years ago on Routwr. Thank you, well done plans with pictures. Posts Latest Activity Photos. You'd have to either contact Ridgid and ask them if it can accept attachjent attachment you have in mind, or contact the vendor of the attachment and ask them if their product will ridgid table saw router attachment api this model of Ridgid saw

With the old wing removed, I clamped the angle irons to the new wing through the router insert opening with heavy paper between the angle iron and the new wing. I aligned the top edges of the wing and the Ridgid Table Saw Router Attachment Set table saw top, using my finger as a gauge and tapping gently with a wooden mallet to make fine adjustments. I was careful to align the back edge of the wing against the rear fence rail. By putting all of the difference along the front, I avoided having to shim on both sides.

I used my digital calipers to measure how far the front of the wing casting stood proud of the centre section of the table saw and stacked stainless steel shim stock to sit between the front fence rail and the table top. It came out to be about 0. In retrospect, I probably should have put the error along the rear rail instead of the front but it seems to work OK. After re-installing the front fence rail, I discovered that I needed to drill a hole through the wing casting to accept the fence rail mounting bolt.

Drilling cast iron is easy — lubricate Ridgid Table Saw Router Attachment Google and drill with progressively larger drills to reach your desired size. In the pictures, you can see my new router lift. There was nothing to installing that beyond following the instruction manual. My initial impressions are really positive. Doing this has had the desired effect of eliminating my free standing router table.

I bought them at the same time. Installed and […]. Thanks again, Derek! I am looking at purchasing the same cast top and a JessEm lift, did you have to do any modifications to get the lift plate to fit and anchor into the cast top? The dimensions of the plate opening on the casting and the dimensions of the lift plate are theoretically the same. The first time I installed the JessEm lift, it was quite a snug fit, but it went in.

As for anchoring, the lift plate sits on several grub screws, and I never felt a need to anchor it down beyond gravity and friction. I suppose if you want, you Ridgid Table Saw Router Attachment Guide can drill the cast iron and use the countersunk holes at the corners of the plate with a machine screw, nut and fender washer. Having used this combination for more than a year now, I am still very, very happy. Hi Derek, thanks for this inspirational and informative post. Hi Dustin, The fence rail on my Ridgid saw is an aluminum extrusion and it attaches to the cast iron table with a T-slot.

I do have a bolt running through the side of the router wing into that T-slot on the front fence rail, but not the back. I added that bolt so that the cast iron would support the fence rail, not so the fence rail would support the cast iron. You can check out my article about installing it on my Ridgid Ts for more information about the router wing itself, and I also have an article about the low-priced […].

Built using WordPress and the Materialis Theme. The best answers are voted up and rise to the top. Stack Overflow for Teams — Collaborate and share knowledge with a private group. Create a free Team What is Teams? Learn more. Can I mount a router to the Ridgid R table saw? Ask Question. Asked 8 years, 2 months ago.

Active 7 years, 5 months ago. Viewed 2k times. Improve this question. Brad Mace 2, 7 7 gold badges 32 32 silver badges 46 46 bronze badges. Jeremy Foster Jeremy Foster 1 1 gold badge 1 1 silver badge 9 Router Table Attachment For Ridgid Table Saw Value 9 bronze badges. You'd have to either contact Ridgid and ask them if it can accept the attachment you have in mind, or contact the vendor of the attachment and ask them if their product will fit this model of Ridgid saw Add a comment.

Active Oldest Votes. Improve this answer. Answers that relay on links are only useful if the link does not die.

Please consider describing some of the information in the link, so the information can live on even if the link dies. Sign up or log in Sign up using Google.

Do It Yourself Wood Fence Installation Online Woodcrafters Supply 600