As soon as you put suqare metal woodworking square youtube posts in the ground, moisture and wood rot begin to take a toll. Sorry about that folks, I had to walk through a cloud of something weird on metal woodworking square youtube way past all the other cubes to get from the shop to my desk, and it seems to have affected me for a moment. Molten metal belongs on your workpiece, not on your foot. You can get a drafting square at most large office or art supply stores. At squafe point, really double check your work.

Deep breath. And another one. OK, I think I can write now. Unusual Woodworking Square Hole Drill Bit Mortising Chisel Set Youtube as it may seem, this blog post is about how to make a tool to make woodworking easier and more accurate. What do you use when you need a big square for layout work? A rafter or framing square will work, but they are awkward to use and not the most accurate devices. A combination square like I wrote about in the June issue is good for small work, but the reference surface and straightedge can be too small for laying out a cabinet.

The trouble is, they were designed to be held against the edge of a T-square, so they lack a built-in reference. The answer, as it does in about 90 percent of woodworking, comes from the scrap bin. After making sure it was nice and straight, and trimming it to length, I used a thin-kerf rip blade in the table saw to make a groove about half the thickness, down the middle of the stick. This size groove was just a trifle bigger than the thickness of the square, so I used some Gorilla Glue to bond the plastic to the wood.

I put a couple of spring clamps on to keep the expanding glue from pushing the square out of the bottom of the groove. When the glue was dry, I trimmed the foam-out off with a chisel, and took the square for a test drive.

The only things to worry about when you make one are to get the wood as straight as you can, and keep of the depth of the groove consistent. I used a zero-clearance insert on the saw, and kept steady downward pressure on the wood as I milled the groove. It rides along the rip fence and lets you make small stuff safely.

I daresay this bespoke gem works a treat. You can get a drafting square at most large office or art supply stores. Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality. My hat is off to Bob for making me laugh out loud.

Seems to me you just go ahead and make the rest of it and forget the drafting square. Another alternative, frankly much easier, is just to glue a nice, trued up piece of stable stock to the drafting square using five minute epoxy. The whole bit of running a groove with a table saw is a nonstarter for me. I can sure square up an offcut Metal Woodworking Square Zip by hand though. No problem. I would like to take it a bit further. I wanted my square to be square on all surfaces, like my metal ones.

I glued mine with a square on the inside, so the inside faces would be square to one another. Once dry, I used the miter slot and front edge of my table saw to check it for square. It is a little harder to true this edge of the thinner board, but a little work with a block plane and chisel will get it. This lets me mark with the two inside edges. Next I trued the outside edge of the thinner board to the inside edge of the thicker board. This lets me mark using the inside edge of the thicker board against the board I am marking and then mark off the outside edge of the thinner board.

Last I trued the outside edge of the thicker board to the outside edge of the thinner board. Now all the edges are true. This sounds a little confusing, but if you read this with your trisquare in your hand, it will make sense. I enjoyed your article and video on making the Try Square, but I have t wo questions. The illustration from p. Also, what kind of glue were you using and how long do you have to square up the Try Square before the glue starts to set and make further movement difficult or impossible?

Thanks again, Lee leehockman yahoo. By Graham Haydon. Product Recommendations. Benjamin Seaton , Try Square. Graham Haydon is a Joiner based in the UK, working in the same woodworking business his great grandfather started in alongside his father, brother and a small team of craftspeople.

The business makes custom architectural Round Square Woodworking Youtube joinery, simple furniture and custom kitchens Metal Woodworking Square Quest along with a variety of other woodworking projects. During his spare time he enjoys woodworking mainly with hand tools. Graham, Your videos are works of art. Shawn Nichols September 29, Hey Graham, can you do a blog post on your bench? Great video! Much obliged, Shawn. All rights reserved Privacy Policy Terms of Use.

Best Rap Hashtags Name Best Rap Albums Last 3 Years Kit 9 Inch Table Saw Blades For Sale