На товары категории «Другое» действует доступная цена, поэтому MASTERCRAFT BELT DISC SANDER BELT MADE IN THE USA можно приобрести всего за руб. Не можете сделать выбор? Посмотрите другие товары продавца bandsaw-tire-warehouse () – «Смотреть все товары». Mastercraft Belt/Disc sander review. Very easy to setup and runs smoothly and quietly. This sander had plenty of power eliminating stalling during use. Another quality Mastercraft product. Is this review written as part of a Canadian Tire contest/promotion? Доставка ручных электроинструментов для дома и запчастей для электроинструментов Sander с интернет-магазина www.- из США от 6 дней через сервис покупок за рубежом ShopoTam. Покупайте ручные электроинструменты для дома и запчасти для электроинструмента Sander по низким ценам прямо сейчас.

Table Of Contents. Quick Links. Parts Missing or Damaged? Toll-Free Helpline: Table of Contents. Previous Page.

Next Page. Sander MasterCraft Instruction Manual 3 x 21" belt sander 11 pages. Failure to observe any of the following instructions could result in severe personal injury to tool user and bystanders or cause damage to tool and property! Page 5: Before You Start Mastercraft belt and disc sander manual quality Instructions Before You Start — Electrical In the event of a malfunction or short circuit, grounding provides the path of least resistance for electrical current and reduces the risk of electric shock for the operator.

This tool is equipped with an electric cord that has an equipment grounding conductor and a grounding plug. Repair or replace damaged or worn cords immediately. Be sure your extension cord is properly wired and in good condition. Do not use damaged extension cords. Carefully remove all parts from the shipping carton. Page 8 Installation of Sanding Disc and Guard 1. Peel backing away from sanding disc. Locate table support and 3 hex head screws, washers and locking washers in loose parts bag.

Place table top-down on a flat surface. Mastercraft belt and disc sander manual quality table support against table bottom, aligning holes on support with pre-drilled holes in table.

Page 10 Installation of Belt-Sander work support 1. Locate work support and hex screw, washer and locking washer. Hold work support in position and fasten as shown.

Do not overtighten. Turn the power off and remove the plug from the outlet before changing the accessories. Removal: 1. Slide tension lever to the right to release the belt tension. Slide the used sanding belt off of the rotational mechanism. Installation: 1. Page 12 To properly track the sanding belt: 1. Plug in the sander. Turn power switch ON, then immediately OFF, noting whether the belt tends to slide off its track, and to which side front or back of the sander.

If the sanding disc did not tend to either mastercraft belt and disc sander manual quality, it is tracking properly. Page 13 Sanding operations are inherently dusty. Depending on operator needs and the workpiece, the work-support can be used with either the horizontal or vertical position.

Page 15 Surface Sanding on the Sanding Belt When sanding flat, broad surfaces on the belt sander, hold the workpiece firmly but lightly onto the surface of the belt and against the work support work restkeeping fingers away from the sanding belt.

Page 16 Sanding Disc Station - Sanding Outside Curves Always sand outside mastercraft belt and disc sander manual quality using the sanding disc and moving the workpiece from the left side of centre, as shown. Keep the curve pressed firmly against the sanding disc, moving the work evenly from the left side of the sanding disc. DO NOT attempt to repair or maintain the electrical components of the motor. Take the sander to a qualified service technician for this type of maintenance.

Ensure sanding rub off belt or Mastercraft Belt And Disc Sander Manual 2019 discs. Page 19 Motor overheats. Motor overloaded. Reduce load on motor 2. Utilize an extension cord of appropriate gauge and length or plug tool directly into outlet. Motor stalls resulting in 1. Page 20 Parts Schematic Print page 1 Print document 22 pages. Cancel Delete. Sign In OR.

Don't have an account? Sign up! Restore password. Upload from disk. Upload from URL.

Find the user manual you need for your tools and more at ManualsOnline. disc belt sander. MasterCraft Sander 55 4. 0 Solutions. I am looking for a part for my belt and disc sande. MasterCraft Sander 0 Solutions. i need a part for a mastercraft belt sander MasterCraft Sander 0 Solutions. Belt/Disc Sander. View and Download MasterCraft owner's manual online. Belt & Disc Sander. sander pdf manual download. Use different abrasive grits on your sander’s belt and disc. For example, use an or grit belt for shaping, and a or disc for detailing. Sanders create choking dust that must be sucked up by a vacuum or dust collector. A single 4" port on the Jet JSGOS and Powermatic serves both belt and disc; the Jet fared best.

Electric Tools For Wood Carving Table Diy Wood Reptile Enclosure Model