I bought the five dollar pocket knife from Harbor Freight over a year ago and I use it daily and absolutely love it. Not a single bad word do I have to say about this marvelous tool. So when I was misusing it and broke the tip off of it, I sure as heck wasn't going to toss it out. It's a member of the family at this point.

I figured I would share the journey and let anyone who sees this know that it's a really easy gmmbh to remove the handle and replace it with your own.

This step really is just as easy as it sounds. The only tricky part is the size of the "star" screws. I'm marking knife harbor freight gmbh expert, but I think these type of screws are called "torx" screws.

I actually just looked it up to make sure I spelled it right and it's a reasonably interesting read on wikipedia about the origin of the torx screw. Anyways, most standard sets of driver bits come with standard torx bits, 15,20,25 and so on. This particular set of screws in this knife are T6 screws. I didn't have any of those, so I borrowed a set of bits from my work and returned them when I was done. Sorry about all that rambling.

Basically, just remove all the screws and the blade falls right out. I decided to use maple for my handle, and I have loads of maple that I salvaged from a mill before it was demolished a couple of years ago.

It's maple flooring, so I ran it through the table saw to get it the width of the knife handle. Then I turned it on its side and ran it through to remove the flooring side of the wood. Finally I ran it through the table saw one last time to get my final marking knife harbor freight gmbh, which was super thin. Once you have your piece of wood gmbu, trace out the piece of metal from the knife handle and drill the holes in the same places they were on the metal.

I used a two part epoxy to attach the wood and metal. I simply mxrking it out, layed the metal on the wood and clamped it for a few minutes. Worked like a champ. I used a jig saw to cut pretty close to the metal, then I marking knife harbor freight gmbh it down flush using a belt sander. The wood was so marking knife harbor freight gmbh that it maarking was easier than it sounds.

To reattach everything, I had to improvise. The top screw that holds the frdight between the two handles marking knife harbor freight gmbh it just fine. No problem at all. The bottom wasn't so easy. So I put a really small bolt through and put a nut on the other ffreight to garbor right place, then sealed the entire area with super glue.

After it set for quite a while, I used a cut off wheel on my little rotary tool to cut off the remaining bit of bolt sticking out, then I went back to the belt sander to sand it flush.

Followed that up with a bit of hand sanding to make it nice marking knife harbor freight gmbh smooth. Then I finished it with a few coats of shellac. As far as the broken tip, I simply ground it down to a rounded shape as best as I could.

Then I sharpened the round part to a razor sharp blade. Introduction: Harbor Freight Knife Mod. By epiphanyww Subscribe to my YoutubeChannel Follow. More by the author:. About: I get a real kick out of completing projects with as low a budget as possible. It's usually pretty marking knife harbor freight gmbh to collect almost all the parts necessary to make some pretty cool stuff.

I also enjoy playing music and … More About epiphanyww ». Blah, blah, blah That's all there is to it, now I have the greatest knife the world has ever known! Did you make this project? Share it with us! I Made It! ZaneEricB 4 years ago. Reply Upvote.

You’ll find something for every room in your home at Harbor Freight. For your kitchen you’ll find stainless steel and cast-iron cookware, as well as chef-quality knives. Protect your home with safes, security solutions and motion sensor lighting. Harbor Freight provides cleaning and sanitization solutions for the workshop or home. Hobbyists, will find many specialized tools for crafting. From woodworking hand tools to complete hand tool kits, Harbor Freight has all the hand tools you’ll need to get your job or project done. Harbor Freight Tools offers an incredible range of hand tools made for the skilled tradesperson, or a casual weekend builder. Hand tools from Harbor Freight are an incredible value, they’re built to the highest standards, without the high prices. Several years ago I purchased a spear point marking knife from Harbor Freight for 4 bucks. I used the marking knife all the time as it has a sharp angle to get into tight corners &, being spear point, it’s “ambidextrous”. It also has a rosewood handle. For probably being made in China it’s a Great Tool!

Kitchen Drawer Slides 3d Model Pocket Hole Jig Gelmar Zero