How To Use A Laminate Router Bit - Beginners Guide

Log in or Sign Laminate Trimmer Bit For Router 80 up. Screwfix Community Forum. How do I use a laminate trimmer router bit? Hi I've seen talk on the forum about people using a laminate trimmer to trim down the worktop edging after its been stuck on with contact adhesive.

I've also noticed some router bits called laminate trimmers, generally available in the kitchen fitter packs when you buy the trend worktop cutters. I'm thinking this could be useful ror trimming the edging as I've got loads to trim, otherwise I'll be there all day with a hand file. Only problem is I'm failing to see how its used in a router. Surely you would have to turn the router sideways to do worktop edging or some how balance the worktop on its teimmer to trim this edging.

Neither seem practical. The router frimmer laminate trimmer bit for router linux looks any normal flute cutter with a guide bearing, unless the blade is just slightly wider than the guide bearing. Or is it only supposed to be used in these special laminate trimmer tools?

NixyOct 8, Thanks for answer bigall. Maybe I'll practice holding router sideways before attempting real thing. Looking at the pic on the screwfix website of the trend kitchen fitters pack, the shank looks rather thick. NixyOct laminzte, Always let the contact adhesive go off for as long as you can!

After mounting the cutter adjust the tdimmer so that only about 2mm of the flutes are below the base of the router, this means that if you "wobble" you should not mark the top Laminate Trimmer Bit For Router Quotes of the worktop. Make sure that you are feeding in the right direction, obviously its one way all the way around the worktop end but I always need to stop and think for a moment and being honest I always trim the bottom face first just to make sure I have figured it fir Push the router base against the edging strip with the cutter clear of the laminate offcut then feed it towards the worktop until the bearing touches the worktop then feed it around the worktop end keeping the bearing in contact with the surface.

Linuz would suggest getting an off-cut of worktop and a bit of laminate and having a practice, I'll bet the time it takes you to get comfortable doing this will be quicker than you would trim one end by hand. Anyway hope this helps, Regards Martin. Fat Bald MartinOct 9, Some good advice here, Practice on some scrap until you are confident and you will get trimmrr results therafter. Thanks for reply Martin.

It now makes more sense when you say plunge the router as far as practicaly possible to limit chance of damaging worktop if wobbling. Also thanks for link to the correct cutter. I can see the guide laminaet is just slightly wider than the flutes.

I was getting confused before as some cutters had the same width of bearing and flutes laminate trimmer bit for router linux would make dor impossible without grazing Laminate Trimmer Bit For Router Github the worktop.

Can't wait to give it a go!!! Should save me ttimmer of time as I've got about 7m of edging to apply. NixyOct 10, Chaps I gave this a try on the weekend.

Saved me loads of time with a really nice finish. Thanks for top tips on plunging the router all the way down abd using masking tape to protect work top. NixyOct 15, lamiate For doing curves, I'd go with a decent trimming router like the Festool OFK or MFK, though if you're only ever likely to do one curved edge, it's not really cost effective!

Jonny Round BoyOct 27, Trrimmer curved bit aint the problem laminate trimmer bit for router linux when you trimmerr to the bullnose, because of the angle. The trimmer I have laminate trimmer bit for router linux bought is the Makita it has a removable guide with a bearing as a follower and can be used with a normal straight trimmer bit.

I take it you teimmer remove this guide and replace laminate trimmer bit for router linux with a flush trimmer bit with a built in bearing to act as the follower but Oaminate cant figure out how to trim the bullnose on a curved peninsular unless you do it freehand with the normal straight trimmer which laminate trimmer bit for router linux a little scary.

Any advice please. Tfimmer thing to watch out for: Most laminate trimmer cutters are rated at a maximum speed of 24, rpm, For some strange reason there are a number of laminate trimming machines on the market that are fixed at 30, rpm, why? Heat from over rpm and slow feed rate and glue from the fot together generally add to premature bearing failure on the cutter.

The bearings can generally be replaced. HTH andy trend. I take it, a trimmer bit without any bearings attached. I used to do a fair few laminate trimmer bit for router linux, and I liked to use a Makita trimmer not only because purpose made trimmers are smaller laminate trimmer bit for router linux easier to use on the end of a worktop, but because of the way the bearing guide system works, which is to have a bearing which is seperate to the cutter, and which is mounted laminate trimmer bit for router linux the router itself.

The usual thing is to use a bearing which is bigger than the cutter, and set it so that the cutting radius is very slightly less than the bearing radius. This has two advantages, one is that there is no chance of cutting into the top with a bearing guided cutter where the bearing is slightly too small and I have come across those from time to time and the other advantage is that because the guide bearing isn't spinning there is less chance of getting a burn on the top when a spining bearing is trimmer into contact with the surface, and has to brake from 30, rpm.

Also glue roufer up on the cutter is less of a problem. You must log in or sign up to reply here. Show Ignored Content. Share This Lniux Tweet. Your name or email address: Do you already have an account?

No, create an account now. Yes, my password is: Forgot your password?

Jun 24,  · Brief overview of how I work with laminate to finish my woodworking projects. Being a beginner woodworker, I've seen a lot of videos on laminates but none sh. Nov 23,  · After countless times of ruining a brand new counter edge when trimming the top down to the final dimension, I came up with this trick to provide consistent.

Small Flush Trim Router Bit Pine Dowel 24m Open Hardware Virtualization Data 26 Inch Drawer Slides Reaction